Category Archives: Stages – X and Z

Motion Control – Miniature Voice Coil Servo Motor Features: 12.7 mm Stroke, High Force-to-Size Ratio, and 1 Micron Resolution!

Motion Control – Voice -Coil Stage
motion control - electric cylinder

motion control - moticint

 

 

Van Nuys, CA – Motion Control – Components -– Moticont has released the miniature GVCM-016-019-01M Linear Voice Coil Servo Motor.  Smaller in diameter than a US Dime this 15.9 mm (0.625 in.) diameter Servo motor, also called an Electric Cylinder, features a high force-to-size ratio of 1.5 N (5.3 oz) continuous force and 4.6 N (16.6 oz) of peak force.  The compact housing is just 19.1 mm (0.63 in.) long and in the fully extended position the shaft extends 20.0 mm (0.79 in.) beyond the face of the housing.  The end of the shaft has an M2.2X0.45 thread by 4.0 mm long for backlash free connections.

Motion Control – All New! High Precision, Three-axis Gimbal Mounts with Four Motor Options Offer Greater Flexibility and Stability!

Motion Control – NEW! Three-axis Gimbal Mounts!
motion contol - gimbal mount

motion control - OES Components

 

 

 

Van Nuys, CA —– Motion Control – OES (Optimal Engineering Systems, Inc.) has released four all new Three-axis Azimuth, Angular Elevation, and Roll Gimbal Mounts. These new high precision and high stability AU270-AER Gimbal Mounts locate the surface of the Roll Stage 115 mm below the center line of rotation allowing for the positioning of: Cameras, optics, lasers and instrumentation for scanning, tracking, positioning, pointing, and other applications on their respective centerlines.

Motion Control – Electric Cylinder from Moticont Has Zero Cogging and High Throughput!

Motion Control – Electric Cylinder Has Zero Cogging

motion control - electric cylindermotion control - moticont

 

 

Van Nuys, CA — Motion Control – Moticont has added another non-commutated linear actuator to its DDLM series of low cost actuators.

The 0.125 in. (3.2 mm) diameter shaft has an internal thread on each end, a total of length of 4.960 in (126.0 mm), and extends 1.585 in. (40.3 mm) past the mounting end of the actuator. The shaft extends thru the 3/8-32 UNF x 0.250 (6.4 mm) long threaded studs at each end of the housing which can be used for mounting the DDL-019-070-01 linear actuator. Long life plain linear bearings support the internal shaft at both end of the actuator.

Motion Control – Low Cost, Long Range of Travel, High Precision, Low Profile, Motorized, Profile Rail Linear Guide Stages Are Available from OES

Motion Control – Profile Rail Stages

motion control - linear stages


motion control -oesVan Nuys, CA – — Motion Control – Optimal Engineering Systems, Inc. (OES) has added five new profile single axis positioning stages to their AQ150 Series of linear stages. Available off-the-shelf in travel lengths of: 600 mm (23.622 in.), 700 mm (27.559 in.), 800 mm (31.496 in.), 900 mm (35.433 in.), and 1000 mm ( 39.370 in.), these stages are available with either a Two-Phase Stepper Motor or with a Three-Phase Brushless Motor with a Quadrature Incremental Optical Encoder.

Motion Control – Dual Axis Yaw-and-Pitch Stages Feature Full Range of Motion of Each Axis Under a Single Fixed Point in Space!

Motion Control – Yaw Pitch Stages

motion control - yaw pitch stages

motion control - OES Components

 

 

 

Van Nuys, CA – — Motion Control – A new, series of Dual-axis Yaw-and-Pitch Stages have been introduced by OES (Optimal Engineering Systems, Inc.). This new series of high precision Yaw-and-Pitch stages are ideal for precise measurements of compound curves and angles of an object during inspection or reverse engineering, laser machining and drilling, scanning, tracking, mirror positioning, and for use with coordinate measuring machines and autocollimators.

Motion Control – High Precision 300 MM Motorized Vertical Lift Stage from OES Features: Stability, High Load Capability, and Low Cost!

Motion Control – Vertical Lift Stage

motion control - vertical lift stage

motion control - OES Components

 

 

Van Nuys, CA – — Motion Control – A vertical lift of 300 mm (11.811 in.), high stability, and low cost are just some of the features of the AT20-300 Motorized Vertical Lift Stage from Optimal Engineering Systems, Inc. (OES). This high load, 50 kg (110.2 lbs), vertical lift stage can be easily integrated into almost any application. The large 400 mm x 200 mm (15.748 in. x 7.874 in.) stage has a pattern of threaded mounting holes. The rigid box construction of the moving component of the elevator stage travels on six slide rails assuring smooth vertical travel and parallelism of the table and mounting surface at all times, and features: 3.315 µ (non- Micro-Step) resolution, 5 µ repeatability, and 15 µ positional accuracy.

Motion Control – Large Open Aperture XY Alignment Stages Feature: High Resolution and High Repeatability!

Motion Control – Open Aperture XY Alignment Stage

motion control - alignment stage


motion control - OES

 

 

 

Van Nuys, CA – — Motion Control – New high resolution and high repeatability Alignment Stages have been released by Optimal Engineering Systems, Inc. (OES). Supplied with a standard 4 mm-per-turn ground lead screw, the AU200-200×200 Alignment Stages feature 200 mm (7.874 in.) of travel in both the X and Y axes. These low profile 80 mm (3.179 in.) high XY stages have a 250 mm x 250 mm (9.842 in. x 9.842 in.) open aperture.

Motion Control – Precision Manual XYZ Stage from OES!

Motion Control – Precision Manual XYZ!

motion control - xyz manual Stage
motion control - stage

 

 

Van Nuys, CA —– Motion Control – This manual crossed roller XYZ-axis positioning stage is made of aluminum alloy with an black anodized coating. The table size is 25 x 25 mm has a body weight of 0.16 Kgf. The maximum load of this super thin table is 1 Kgf. The movement accuracy is Straightness 5µm ,Vertical yawing 30″ and Parallel yawing 25″.

Motion Control – Open Aperture XY Stages from OES Feature: High Resolution and High Repeatability!

Motion Control – Open Aperture XY Stages!

motion control- xy stages

Van Nuys, CA – — Motion Control – Two new high resolution, high repeatability XY stages have been released by Optimal Engineering Systems, Inc. (OES). The AU200-15×15-01 Motorized Stage (pictured) and the AU200-15×15-04 Motorized Stage are powered by Two-Phase Stepper Motors and have high 0.25 micron resolution and high 1.5 micron repeatability.

motion control - OES

The AU200-15×15-04 stage includes Quadrature encoders for position verification. Both stages have a large 3.54 in. x 3.54 in. (90 mm x 90 mm) platform with large open aperture and feature standard 1 mm-per-turn ground lead screws, and precision V-grove and Cross Roller guides.

Motion Control – Get Zero Cogging and High Throughput from Low Cost Moticont Linear Actuators!

Motion Control – Electric Cylinder!

motion control - electric cylinder


motion control - moticint

 

Van Nuys, CA — Moticont has introduced their highest force linear actuator in their DDLM Linear Actuator Series. The DDLM-038-051-01Linear Actuator is a low cost non-commutated linear actuator that is easily integrated into new and existing applications, and is the ideal choice when upgrading from a pneumatic system. Compact, clean, and quiet, this fully enclosed linear actuator, also referred to as an electric cylinder, is 1.500 in. (38.1 mm) in diameter with a housing length of 2.00 in. (50.4 mm) long.

Motion Control – Joysticks for Controlling the X, Y, and Z Axes of 1, 2 and 3 axis Stages and Actuators are Plug-and-Play, and Low Cost!

Motion Control – Joysticks

motion control - Joystick
Van Nuys, CA – — OES (Optimal Engineering Systems, Inc.) has expanded its line of Joysticks for 1, 2 and 3 axis Stages and Actuators. These are easy to use, single-handed, ergonomic joysticks that provide proportional control of the X, Y, and Z axis of from one to three actuators. Low, medium, and high speed ranges are button selectable. The X, Y, and Z axis speeds are controlled by the tilt angle of the handle and the angle of rotation of the knob.

motion control - stages - custom

The maximum speeds may be set by the user via the supplied, easy to use GUI.

Motion Control – Optimal Engineering Systems, Inc. (OES) Introduces New, Motorized, High Resolution Pan-Tilt Stages!

Motion Control – Pan-Tilt Stage
motion control pan tilt stage

Van Nuys, CA – — Motion Control – High Resolution, Motorized, Pan-Tilt Stages have been added to the extensive line of OES (Optimal Engineering Systems, Inc.) motion control products. These motorized Pan-Tilt Stages are available in two sizes. The PT60-1 Pan-Tilt Stage is a combination of two 60 mm (2.362 in.) rotary stages and the PT100-1 is a combination of two 100 mm (3.937 in.) rotary stages, set at a 90O angle to each other.
motion control - oes
The rotary stages of each Pan-Tilt stage features a high repeatability of 0.005O (18 arc-sec), a positional accuracy of 0.005O (18 arc-sec), and a resolution of 0.001O = 3.6” (10 Micro-steps per Step Motor Driver in use).

Motion Control – High Precision, XAB Triple-Axis (2 Goniometers and X-Axis) Stage Available from OES!

Motion Control –  Triple-Axis Stage!

motion control - tri-axis stages


motion control - stages - custom

 

 

 

Van Nuys, CA – — Motion Control – Optimal Engineering Systems, Inc. (OES) offers a very low cost solution for the precise measurement of compound angles or the rotation of an object to precise angular positions.

The XAB-050-XX-01 integrates a two-axis Alpha-Beta goniometer on top of a single-axis linear actuator. The Beta-axis has a travel range of +/- 15 degrees with a rotation height of 50 +/- 0.2 mm.

Motion Control – Moticont Adds 1 Inch Stroke, Direct Drive Linear Actuator to Their Patented SDLM Series of Electric Cylinders!

Motion Control –  Electric Cylinders!

motion control - electric Cylinder


motion control - moticont
Van Nuys, CA — Motion Control – The SDLM Series of Electric Cylinders from Moticont now includes a 1.0 inch (25.4 mm) stroke actuator in their compact 0.750 in. (19.1 mm) diameter series of linear actuators. The new SDLM-019-095-01-01 actuator features a continuous force of 6.8 oz (1.9 N) and a peak force of 21.6 oz (6.0 N). A precision linear optical quadrature encoder is integrated and protected inside the actuator housing.

Linear Motion Control – One Piece ETX Linear Bearing/Pillow Blocks Can Be Used In Radioactive Environments!

Motion Control – ETX Pillow Block/Bearings for Radioactive Environments

motion control pillow blocks/bearings

E. Longmeadow, MA Motion — Control Components – Linear Motion – LM76 now offers one piece ETX Linear Bearing/Pillow Blocks that will not degrade in a radioactive environment! Machined from a solid block of self lubricating ETX, linear bearing-blocks have high strength, excellent wear resistance, low coefficient of friction, and excellent dimensional stability at higher temperatures As there is no other materials such as PTFE seals or lubricants these bearing-blocks are maintenance free. Custom designed for use in a nuclear power plant these linear bearing/pillow blocks travel on ceramic coated shafting (also supplied by LM76) completely submerged in radioactive water.

To see the “Motion Control Application – ETX Pillow/Block Bearings for Radioactive Environments” CLICK HERE

motion control - lm76

Designed with a slight interference fit between bearing ID and shaft, contaminates are scraped from the shaft’s surface. The low frictional characteristics of ETX have little impact on drive force. They are now available in Inch and Metric sizes.

Motion Control -What To Consider When Specifying A Linear Slide

Motion Control – Tutorial

Considerations when specifying a linear slide for a new or existing application.

By Mike Quinn • LM76

When a design engineer has fully defined a linear-motion application’s requirements regarding travel length, speed, force, and accuracy as well as repeatability, the next question to answer is this:

Does an off-the-shelf linear slide (or a stock linear slide from a catalog) fully satisfy the application?

motion control - linear motion products

Off-the-shelf linear slides are advantageous for their quick delivery and lower cost than that of custom components. No wonder most linear-motion designs do in fact employ off-the-shelf linear slides from various component and system suppliers.

motion control - linear slides

Motion Control – XZ-Axis Motorized Linear Positioning Stages feature 1 Micron Repeatability from Optimal Engineering Systems, Inc. (OES)!

Motion Control – XZ-Axis  Positioning Stages

motion control - XZ stage

motion control -oes

 

 

 

Van Nuys, CA – — Motion Control – OES (Optimal Engineering Systems) has added a new series of 15 mm, 30 mm, 50 mm, and 75 mm Linear Motion Positioning Stages to their broad selection of precision motion control components. Each of these motorized XZ-Axis Linear Positioning Stages features 1 micron repeatability and 10 micron positional accuracy. Both the X-axis (horizontal axis) and the Z-axis (vertical axis) have the travel lengths of 15 mm, 30 mm, 50 mm, and 75 mm and even longer to meet your application requirements.