Category Archives: Stages – Goniometer

Motion Control – Low Cost, High Precision Vertical Lift Stage from OES!

Motion Control – Vertical Lift Stage

motion control - vertical stage

motion control - OES

 

 

 

Van Nuys, CA – — Motion Control – The AT10-120 Motorized Vertical Stage from Optimal Engineering Systems, Inc. (OES) is a high resolution, low profile, high load vertical lift stage that can be easily integrated into almost any application. The large 220 mm x 140 mm (8.7 in. 5.5 in.) drilled and tapped platform has a vertical travel of 110 mm (4.3 In.).

Motion Control – 1, 2, 3 and 4 Axes of Motion Controllers for Servos and Steppers are Low Cost and Plug-and-Play!

Motion Control – Motion Controllers for Servos and Steppers!


Van Nuys, CA – — Motion Control – Need a quick and easy solution to install a single or multi-axis Plug-and-Play motion controller? The answer: The MCC Series of stepper and servo motor controllers from OES (Optimal Engineering Systems) which are designed to control from one to four axes of motion for users without prior motion control experience. These MCC controllers integrate a motion control card and operator interface in one package. Having a user-friendly interface, they allow the user to operate the motion controller, without the need for a PC, PLC, host controller, or programming.

motion control - stages - custom

 

 

The modes of operations are: Set Acceleration, Set Velocity, Set Position, Absolute Move, Relative Move, Find Home, Reset Position Counter, Go to Position Zero, Joystick Operation and Stop All Motors. The MCC Controllers feature a 4-Line LCD, 32-button keypad, STEP and DIRECTION outputs for each axis.

Motion Control – Open Aperture XY Stages from OES Feature: High Resolution and High Repeatability!

Motion Control – Open Aperture XY Stages!

motion control- xy stages

Van Nuys, CA – — Motion Control – Two new high resolution, high repeatability XY stages have been released by Optimal Engineering Systems, Inc. (OES). The AU200-15×15-01 Motorized Stage (pictured) and the AU200-15×15-04 Motorized Stage are powered by Two-Phase Stepper Motors and have high 0.25 micron resolution and high 1.5 micron repeatability.

motion control - OES

The AU200-15×15-04 stage includes Quadrature encoders for position verification. Both stages have a large 3.54 in. x 3.54 in. (90 mm x 90 mm) platform with large open aperture and feature standard 1 mm-per-turn ground lead screws, and precision V-grove and Cross Roller guides.

Motion Control – Joysticks for Controlling the X, Y, and Z Axes of 1, 2 and 3 axis Stages and Actuators are Plug-and-Play, and Low Cost!

Motion Control – Joysticks

motion control - Joystick
Van Nuys, CA – — OES (Optimal Engineering Systems, Inc.) has expanded its line of Joysticks for 1, 2 and 3 axis Stages and Actuators. These are easy to use, single-handed, ergonomic joysticks that provide proportional control of the X, Y, and Z axis of from one to three actuators. Low, medium, and high speed ranges are button selectable. The X, Y, and Z axis speeds are controlled by the tilt angle of the handle and the angle of rotation of the knob.

motion control - stages - custom

The maximum speeds may be set by the user via the supplied, easy to use GUI.

Motion Control – Optimal Engineering Systems, Inc. (OES) Introduces New, Motorized, High Resolution Pan-Tilt Stages!

Motion Control – Pan-Tilt Stage
motion control pan tilt stage

Van Nuys, CA – — Motion Control – High Resolution, Motorized, Pan-Tilt Stages have been added to the extensive line of OES (Optimal Engineering Systems, Inc.) motion control products. These motorized Pan-Tilt Stages are available in two sizes. The PT60-1 Pan-Tilt Stage is a combination of two 60 mm (2.362 in.) rotary stages and the PT100-1 is a combination of two 100 mm (3.937 in.) rotary stages, set at a 90O angle to each other.
motion control - oes
The rotary stages of each Pan-Tilt stage features a high repeatability of 0.005O (18 arc-sec), a positional accuracy of 0.005O (18 arc-sec), and a resolution of 0.001O = 3.6” (10 Micro-steps per Step Motor Driver in use).

Motion Control – High Precision, XAB Triple-Axis (2 Goniometers and X-Axis) Stage Available from OES!

Motion Control –  Triple-Axis Stage!

motion control - tri-axis stages


motion control - stages - custom

 

 

 

Van Nuys, CA – — Motion Control – Optimal Engineering Systems, Inc. (OES) offers a very low cost solution for the precise measurement of compound angles or the rotation of an object to precise angular positions.

The XAB-050-XX-01 integrates a two-axis Alpha-Beta goniometer on top of a single-axis linear actuator. The Beta-axis has a travel range of +/- 15 degrees with a rotation height of 50 +/- 0.2 mm.

Motion Control – Low Cost, Long Range of Travel, High Precision, Low Profile, Motorized, Profile Rail Linear Guide Stages Are Available from OES

Motion Control – Profile Rail Stages

motion control - linear stages


motion control -oesVan Nuys, CA – — Motion Control – Optimal Engineering Systems, Inc. (OES) has added five new profile single axis positioning stages to their AQ150 Series of linear stages. Available off-the-shelf in travel lengths of: 600 mm (23.622 in.), 700 mm (27.559 in.), 800 mm (31.496 in.), 900 mm (35.433 in.), and 1000 mm ( 39.370 in.), these stages are available with either a Two-Phase Stepper Motor or with a Three-Phase Brushless Motor with a Quadrature Incremental Optical Encoder.

Motion Control – High Precision, Low Cost, Stacked Goniometer Stages from OES!

Motion Control Stacked Goniometer Stage from OES

OES Logo

Van Nuys, CA – — Motion Control –- Goniometer stages can measure angles of objects such as crystals or move an object to a precise angular position along an arc, in relation to a fixed point in space. Two goniometer stages mounted in an alpha-beta configuration (stacked) can rotate an object around a fixed point in space on a spherical surface. Optimal Engineering Systems (OES) offers stacked, precision aligned goniometer stages with a rotation center 50 mm above the upper stage. The lower (AK110-10) goniometer stage features a 65 mm x 65 mm table, ± 10O of rotation at a rate of 7O per sec. The upper (AK110-15) goniometer stage features a 65 mm x 65 mm table, ± 15O of rotation at a rate of 10O per sec. The accuracies for each unit are; repeatability: ± 4″ (240 arcseconds), typical positional accuracy: ± 9″ (540 arcseconds), and typical backlash is ± 3″ (180 arcseconds). Goniometers and stacked goniometers are used for: Identifying crystals, examining cutting edges of medical instruments, estimating hyperspectral bidirectional reflectance, gloss measurements, measurements of radiation patterns of LEDs, Directing lasers, aligning mirrors, and manufacturing of quartz oscillator plates using quartz cutting x-rays.

The precision, compact AK110-15-10 Goniometer stacked stage, available with either stepper, servo motors, optical encoders or manual adjustment knobs. It has a footprint of just 169 mm x 169 mm, and can be supplied plug-and-play with a motion controller. It is easily integrated into an inspection, testing, or manufacturing environment.

About OES Optimal Engineering Systems, Inc. (OES) is a manufacturer of motion control products including: Stepper motor controllers and drivers, solenoid electronics, and positioning stages and slides. Applications include: Animation, automated assembly systems, automation, CNC machines, flight simulation, inspection systems, linear and rotary stages, machine tools, medical devices, motion control camera boom systems, optical comparators, CMMs, pan-tilt gimbals, PCB assembly & inspection, pick-and-place, positioning stages, robotics, scanners, security cameras, telescope drive mechanisms, time-lapse photography and winders

Some of the industries OES serves are: Aerospace, Astronomy, Chemical, Communications, Educational Institutes, University, Colleges, Government Agencies, National Labs, Manufacturing, Medical, Metrology, Military, Motion Control, Museum, News Agencies, Semiconductor and Test Equipment. Optimal Engineering Systems, Inc’s. competitive advantage is its state-of-the-art in-house manufacturing facility in North America enabling OES to supply clients with custom designed orders or high volume just-in-time deliveries globally.ve advantage is its state-of-the-art in-house manufacturing facility in North America enabling OES to supply clients with custom designed orders or high volume just-in-time deliveries globally.

For additional information contact Customer Service at Optimal Engineering Systems, Inc. (OES) , 6901 Woodley Ave, Van Nuys, CA 91406; Tel: 888-7071-1826, +1 (818) 222-9200, E-Mail: sales@oesincorp.com or visit the website at http://www.oesincorp.com

OES Logo
Visit OES Website
OES Facebook
OES Twitter
OES Videos

Motion Control – High Precision Motorized Goniometer Stage from OES!

OES Motorized Goniometer Stage

OES Logo

Van Nuys, CA – Motion Control – Optimal Engineering Systems, Inc. (OES) offers a very low cost solution for the precise measurement of angles or the rotation of an object to a precise angular position. This 160 mm x 160 mm stage with +/- 15o of rotation at speeds to 10o/sec, features a 400:1 worm gear ratio and a resolution of 0.0005o with a 10 micro-step per step stepper motor driver; the stage is also available with a servo motor and optical encoder. This low profile Goniometer stage is just 100 mm high and the height of the rotation center at 139 mm is ideal for: Crystallography, light measurement, measurement of surgical cutting blades, microscopy, laser positioning, and inspection applications.

The precision worm gear and crossed roller guides provide the high precision, (Repeatability of +/- 3 arcsec, Accuracy of +/- 8 arcsec, and Backlash of +/- 3 arcsec) needed for critical measurement and inspection operations. This compact, black anodized Motorized Goniometer Stage measures just 340.5 mm long (including the standard (1.8o) stepper motor and 160 mm wide and can handle loads to 30 Kg. Mounting holes on the stage and in the base assure easy integration into an application. A calibrated indicator displays the angle of rotation, a hand knob is provided for manual adjustment, and the stage can be ordered with a fully compatible controller from OES.

About OES Optimal Engineering Systems, Inc. (OES) is a manufacturer of motion control products including: Stepper motor controllers and drivers, solenoid electronics, and positioning stages and slides. Applications include: Animation, automated assembly systems, automation, CNC machines, flight simulation, inspection systems, linear and rotary stages, machine tools, medical devices, motion control camera boom systems, optical comparators, CMMs, pan-tilt gimbals, PCB assembly & inspection, pick-and-place, positioning stages, robotics, scanners, security cameras, telescope drive mechanisms, time-lapse photography and winders

Some of the industries OES serves are: Aerospace, Astronomy, Chemical, Communications, Educational Institutes, University, Colleges, Government Agencies, National Labs, Manufacturing, Medical, Metrology, Military, Motion Control, Museum, News Agencies, Semiconductor and Test Equipment. Optimal Engineering Systems, Inc’s. competitive advantage is its state-of-the-art in-house manufacturing facility in North America enabling OES to supply clients with custom designed orders or high volume just-in-time deliveries globally.ve advantage is its state-of-the-art in-house manufacturing facility in North America enabling OES to supply clients with custom designed orders or high volume just-in-time deliveries globally.

For additional information contact Customer Service at Optimal Engineering Systems, Inc. (OES) , 6901 Woodley Ave, Van Nuys, CA 91406; Tel: 888-7071-1826, +1 (818) 222-9200, E-Mail: sales@oesincorp.com or visit the website at http://www.oesincorp.com

OES Logo
Visit OES Website
OES Facebook
OES Twitter
OES Videos