Category Archives: Stages – Air Bearing

Motion Control – Hybrid Air Bearing XZ Positioning System from H2W Technologies!

Motion Control – Air Bearing Positioning System!

motion control - xz positioning stage

 


motion control- h2wSanta Clarita, CA —– Motion Control – This hybrid air bearing XZ positioning system uses H2W air bearing linear stepper motor STS-1220-AP4T (horizontal axis) and voice coil positioning stage VCS05-060-LB-01-MH (vertical Z-axis). The horizontal Air Bearing Linear Stepper motor has a 38.0 in [965 mm] stroke and generates 12.0 lbs [53.1 N] of continuous force. It is guided by precision roller bearings along the platen. Integral air bearings are used to maintain the required motor air gap. The vertical Z-axis motor has a 0.50 in [12.1mm] stroke; generates 6.0 lbs [26.7 N] of continuous force and 118.0 lbs [80.1 N] of peak force. The 1.0-micron resolution encoder allows for precise closed loop positioning. It comes supplied with bearings that allow smooth and rigid motion. The motor coil is the moving part of the assembly in order to reduce the moving mass of the axis.

Features:

  • Wall mountable
  • Two axis of coordinated motion
  • Cable carriers to route payload cables

Multi-Axis Stage

Product Details

Horizontal Axis (Single Axis Air Bearing Linear Stepper)

Motor P/N STS-1220-AP4T

Stroke 38 in 965 mm

Force 12 lbs 53.1 N

Vertical Z-Axis (Voice Coil Motor Stage)

Motor P/N NCC03-15-050-2X

Stroke 0.25 in 6.4 mm

Encoder Resolution 1 micron

Force @ 100% Duty 5.0 lbs 22.3 N

Force @ 10% Duty 15.0 lbs 66.8 N

See Video at Youtube:

For additional information contact Mark Wilson at H2W Technologies, 26380 Ferry Ct, Santa Clarita, CA 91350; Tel: 888-702-0540, Fax: 661-251-2067, E-Mail: info@h2wtech.com or visit the website at http://www.h2wtech.com


See this and other Motion Control Components from H2W Technologies featured on:

http://LinearmotionBlogger.com

http://MotionShop.com

http://AllMotionBlogger.com

http://Automation-Blogger.com

http://MotionControlBlogger.com

http://MotionControlBuyersGuide.com

http://MotionControlWeb.com

http://MotionShop.net

http://Catalogs-MotionControl.com

http://Gotcha-Stick.com

http://MotionControlMarketing.com

H2W YouTube Channel

H2W Technologies Blog

motion control- h2w

 

Motion Control Air Bearing Stages from H2W Technologies

Motion Control – Air Bearing Stages
Motion Control Air Bearing Stage

 

Santa Clarita, CA – Motion Control Tutorial Air Bearing Stages.

motion control- h2w

 

 

Motors:
Non-contact 3 Phase Brushless Linear Motor, Ironless Core, commutated either sinusoidally or trapezoidally with Hall Effects. The encapsulated coil assembly moves and the multi pole permanent magnet assembly is stationary. The lightweight coil assembly allows for higher acceleration of light payloads.The ABS positioning stage is a high precision, granite base, air bearing positioning stage for high end positioning applications. It is driven by an ironless core, non-cogging 3 phase brushless linear motor and guided by 5 flat magnetically preloaded air bearings floating on a granite base.

The ironless core coil assembly is used as the drive mechanism for the AB stage because of its smooth, non-cogging operation. The lightweight of the coil and table assembly allows for high acceleration of light loads. The air bearings, which are used for supporting and guiding the payload, float on a cushion of air. This ensures that there are no wearing components in the system. The air bearings are not limited to acceleration limits like their mechanical counterparts where balls and rollers can slide instead of roll at high accelerations. The stiff cross section of the granite base of the stage ensures a flat straight stable platform for the payload to ride on and does not require any special mounting considerations. Bellows (folded way covers) with a 12:1 extension to compression ratio may be added to an ABS stage.The power for the moving 3 phase coil assembly, encoder and limit switches is routed through shielded flat ribbon cable. Special consideration was made to separate the power and signal cables from each other to reduce the effects of noise on the system. The power cable for the coil assembly and a vacant cable for the customers payload power usage are installed on one side of the stage and the encoder signal, limit switch and an additional vacant signal cable for the customers payload signal usage is provided on the other side of the stage. Standard connectors are provided. The ABS positioning stage incorporates the latest in linear motion technology:
Bearings: Linear guidance is achieved by using magnetically preloaded, porous carbon or ceramic air bearings; 3 on the top surface and 2 on the side surface. The bearings are mounted on spherical surfaces. Clean, dry filtered air must be supplied to the moving table of the ABS stage.
Encoders: Non-contact glass or metal scale optical linear encoders with a reference mark for homing. Multiple reference marks are available and are spaced every 50 mm down the length of the scale. Typical encoder output is A and B square wave signals but sinusoidal output is available as an option

Limit Switches: End of travel limit switches are included at both ends of the stroke. The switches can be either active high (5V to 24V) or active low. The switches can be used to shut down the amplifier or to signal the controller that an error has occurred. The limit switches are typically an integral part of the encoder, but can be mounted separately if required.
Cable Carriers: Cable guidance is achieved by using flat, shielded ribbon cable. Two additional unused shielded flat ribbon cables are supplied for customer usage with the stage. The 2 power cables for the stage and customer payload are installed on one side of the stage and the 2 signal cables for encoder, limit switch and customer payload are installed separately on the of the stage.
Bellows: The ABS comes standard with neoprene / nylon bellows with Mylar stiffeners.
Hard Stops: Hard stops are incorporated into the ends of the stage to prevent over travel damage in the event of servo system failure.

               Advantages: