Category Archives: Stage – Goniometer

Motion Control – All New! High Precision, Three-axis Gimbal Mounts with Four Motor Options Offer Greater Flexibility and Stability!

Motion Control – NEW! Three-axis Gimbal Mounts!
motion contol - gimbal mount

motion control - OES Components

 

 

 

Van Nuys, CA —– Motion Control – OES (Optimal Engineering Systems, Inc.) has released four all new Three-axis Azimuth, Angular Elevation, and Roll Gimbal Mounts. These new high precision and high stability AU270-AER Gimbal Mounts locate the surface of the Roll Stage 115 mm below the center line of rotation allowing for the positioning of: Cameras, optics, lasers and instrumentation for scanning, tracking, positioning, pointing, and other applications on their respective centerlines.

Motion Control – NEW! Elevator Stages from OES Feature 0.03 micron Resolution!

Motion Control – 0.03 micron Resolution Elevator Stage!

motion control - elevator stage


motion control - OES

 

 

 

Van Nuys, CA – — Motion Control – Two new motorized elevator stages, the DAG20-120-01 and the DAG20-120-04 have been released by Optimal Engineering Systems, Inc. (OES).  These high resolution, compact, low profile elevator stages feature high stability 120 mm x 120 mm tables and 20 mm of vertical travel.  High precision ball bearing profile rails assure very high parallelism and smooth motion throughout the raising and lowering of the table.  These Z-Axis Stages are ideal for: Microscopy, inspection, metrology, positioning, photonics, sampling, and laser drilling and machining.

Motion Control – Dual Axis Yaw-and-Pitch Stages Feature Full Range of Motion of Each Axis Under a Single Fixed Point in Space!

Motion Control – Yaw Pitch Stages

motion control - yaw pitch stages

motion control - OES Components

 

 

 

Van Nuys, CA – — Motion Control – A new, series of Dual-axis Yaw-and-Pitch Stages have been introduced by OES (Optimal Engineering Systems, Inc.). This new series of high precision Yaw-and-Pitch stages are ideal for precise measurements of compound curves and angles of an object during inspection or reverse engineering, laser machining and drilling, scanning, tracking, mirror positioning, and for use with coordinate measuring machines and autocollimators.

Motion Control – High Precision 300 MM Motorized Vertical Lift Stage from OES Features: Stability, High Load Capability, and Low Cost!

Motion Control – Vertical Lift Stage

motion control - vertical lift stage

motion control - OES Components

 

 

Van Nuys, CA – — Motion Control – A vertical lift of 300 mm (11.811 in.), high stability, and low cost are just some of the features of the AT20-300 Motorized Vertical Lift Stage from Optimal Engineering Systems, Inc. (OES). This high load, 50 kg (110.2 lbs), vertical lift stage can be easily integrated into almost any application. The large 400 mm x 200 mm (15.748 in. x 7.874 in.) stage has a pattern of threaded mounting holes. The rigid box construction of the moving component of the elevator stage travels on six slide rails assuring smooth vertical travel and parallelism of the table and mounting surface at all times, and features: 3.315 µ (non- Micro-Step) resolution, 5 µ repeatability, and 15 µ positional accuracy.

Motion Control – Large Open Aperture XY Alignment Stages Feature: High Resolution and High Repeatability!

Motion Control – Open Aperture XY Alignment Stage

motion control - alignment stage


motion control - OES

 

 

 

Van Nuys, CA – — Motion Control – New high resolution and high repeatability Alignment Stages have been released by Optimal Engineering Systems, Inc. (OES). Supplied with a standard 4 mm-per-turn ground lead screw, the AU200-200×200 Alignment Stages feature 200 mm (7.874 in.) of travel in both the X and Y axes. These low profile 80 mm (3.179 in.) high XY stages have a 250 mm x 250 mm (9.842 in. x 9.842 in.) open aperture.

Motion Control – 1, 2, 3 and 4 Axes of Motion Controllers for Servos and Steppers are Low Cost and Plug-and-Play!

Motion Control – Motion Controllers for Servos and Steppers!


Van Nuys, CA – — Motion Control – Need a quick and easy solution to install a single or multi-axis Plug-and-Play motion controller? The answer: The MCC Series of stepper and servo motor controllers from OES (Optimal Engineering Systems) which are designed to control from one to four axes of motion for users without prior motion control experience. These MCC controllers integrate a motion control card and operator interface in one package. Having a user-friendly interface, they allow the user to operate the motion controller, without the need for a PC, PLC, host controller, or programming.

motion control - stages - custom

 

 

The modes of operations are: Set Acceleration, Set Velocity, Set Position, Absolute Move, Relative Move, Find Home, Reset Position Counter, Go to Position Zero, Joystick Operation and Stop All Motors. The MCC Controllers feature a 4-Line LCD, 32-button keypad, STEP and DIRECTION outputs for each axis.

Motion Control – Open Aperture XY Stages from OES Feature: High Resolution and High Repeatability!

Motion Control – Open Aperture XY Stages!

motion control- xy stages

Van Nuys, CA – — Motion Control – Two new high resolution, high repeatability XY stages have been released by Optimal Engineering Systems, Inc. (OES). The AU200-15×15-01 Motorized Stage (pictured) and the AU200-15×15-04 Motorized Stage are powered by Two-Phase Stepper Motors and have high 0.25 micron resolution and high 1.5 micron repeatability.

motion control - OES

The AU200-15×15-04 stage includes Quadrature encoders for position verification. Both stages have a large 3.54 in. x 3.54 in. (90 mm x 90 mm) platform with large open aperture and feature standard 1 mm-per-turn ground lead screws, and precision V-grove and Cross Roller guides.

Motion Control – Joysticks for Controlling the X, Y, and Z Axes of 1, 2 and 3 axis Stages and Actuators are Plug-and-Play, and Low Cost!

Motion Control – Joysticks

motion control - Joystick
Van Nuys, CA – — OES (Optimal Engineering Systems, Inc.) has expanded its line of Joysticks for 1, 2 and 3 axis Stages and Actuators. These are easy to use, single-handed, ergonomic joysticks that provide proportional control of the X, Y, and Z axis of from one to three actuators. Low, medium, and high speed ranges are button selectable. The X, Y, and Z axis speeds are controlled by the tilt angle of the handle and the angle of rotation of the knob.

motion control - stages - custom

The maximum speeds may be set by the user via the supplied, easy to use GUI.

Motion Control – Optimal Engineering Systems, Inc. (OES) Introduces New, Motorized, High Resolution Pan-Tilt Stages!

Motion Control – Pan-Tilt Stage
motion control pan tilt stage

Van Nuys, CA – — Motion Control – High Resolution, Motorized, Pan-Tilt Stages have been added to the extensive line of OES (Optimal Engineering Systems, Inc.) motion control products. These motorized Pan-Tilt Stages are available in two sizes. The PT60-1 Pan-Tilt Stage is a combination of two 60 mm (2.362 in.) rotary stages and the PT100-1 is a combination of two 100 mm (3.937 in.) rotary stages, set at a 90O angle to each other.
motion control - oes
The rotary stages of each Pan-Tilt stage features a high repeatability of 0.005O (18 arc-sec), a positional accuracy of 0.005O (18 arc-sec), and a resolution of 0.001O = 3.6” (10 Micro-steps per Step Motor Driver in use).

Motion Control – High Precision, XAB Triple-Axis (2 Goniometers and X-Axis) Stage Available from OES!

Motion Control –  Triple-Axis Stage!

motion control - tri-axis stages


motion control - stages - custom

 

 

 

Van Nuys, CA – — Motion Control – Optimal Engineering Systems, Inc. (OES) offers a very low cost solution for the precise measurement of compound angles or the rotation of an object to precise angular positions.

The XAB-050-XX-01 integrates a two-axis Alpha-Beta goniometer on top of a single-axis linear actuator. The Beta-axis has a travel range of +/- 15 degrees with a rotation height of 50 +/- 0.2 mm.

Motion Control – Precisely Measure Curvature and Angles with New Dual-axis Pitch and Roll Stages!

Motion Control – Dual-axis Pitch and Roll Stages!

motion control | Pitch-and-Roll Stage

Van Nuys, CA – Motion Control – The precise measurements of angles and the curvature of objects are easily determined using two new Pitch and Roll stages just introduced by OES (Optimal Engineering Systems, Inc.). The PR100-45-01 (pictured) is driven by stepper motors and the PR100-45-02 is driven by brushless servo motors with quadrature incremental optical encoders.

motion control - stages - custom

 

The Pitch axis (lower stage) is a high precision goniometer stage which features preloaded cross roller guides and a high ratio worm drive for smooth motion over a range of travel of +/- 45 degrees. It has a typical accuracy of 0.05 degrees and repeatability of +/- 0.01 degrees. Additionally, this axis has end-of-travel limit switches.

Motion Control – High Precision, Low Cost, Stacked Goniometer Stages from OES!

Motion Control Stacked Goniometer Stage from OES

OES Logo

Van Nuys, CA – — Motion Control –- Goniometer stages can measure angles of objects such as crystals or move an object to a precise angular position along an arc, in relation to a fixed point in space. Two goniometer stages mounted in an alpha-beta configuration (stacked) can rotate an object around a fixed point in space on a spherical surface. Optimal Engineering Systems (OES) offers stacked, precision aligned goniometer stages with a rotation center 50 mm above the upper stage. The lower (AK110-10) goniometer stage features a 65 mm x 65 mm table, ± 10O of rotation at a rate of 7O per sec. The upper (AK110-15) goniometer stage features a 65 mm x 65 mm table, ± 15O of rotation at a rate of 10O per sec. The accuracies for each unit are; repeatability: ± 4″ (240 arcseconds), typical positional accuracy: ± 9″ (540 arcseconds), and typical backlash is ± 3″ (180 arcseconds). Goniometers and stacked goniometers are used for: Identifying crystals, examining cutting edges of medical instruments, estimating hyperspectral bidirectional reflectance, gloss measurements, measurements of radiation patterns of LEDs, Directing lasers, aligning mirrors, and manufacturing of quartz oscillator plates using quartz cutting x-rays.

The precision, compact AK110-15-10 Goniometer stacked stage, available with either stepper, servo motors, optical encoders or manual adjustment knobs. It has a footprint of just 169 mm x 169 mm, and can be supplied plug-and-play with a motion controller. It is easily integrated into an inspection, testing, or manufacturing environment.

About OES Optimal Engineering Systems, Inc. (OES) is a manufacturer of motion control products including: Stepper motor controllers and drivers, solenoid electronics, and positioning stages and slides. Applications include: Animation, automated assembly systems, automation, CNC machines, flight simulation, inspection systems, linear and rotary stages, machine tools, medical devices, motion control camera boom systems, optical comparators, CMMs, pan-tilt gimbals, PCB assembly & inspection, pick-and-place, positioning stages, robotics, scanners, security cameras, telescope drive mechanisms, time-lapse photography and winders

Some of the industries OES serves are: Aerospace, Astronomy, Chemical, Communications, Educational Institutes, University, Colleges, Government Agencies, National Labs, Manufacturing, Medical, Metrology, Military, Motion Control, Museum, News Agencies, Semiconductor and Test Equipment. Optimal Engineering Systems, Inc’s. competitive advantage is its state-of-the-art in-house manufacturing facility in North America enabling OES to supply clients with custom designed orders or high volume just-in-time deliveries globally.ve advantage is its state-of-the-art in-house manufacturing facility in North America enabling OES to supply clients with custom designed orders or high volume just-in-time deliveries globally.

For additional information contact Customer Service at Optimal Engineering Systems, Inc. (OES) , 6901 Woodley Ave, Van Nuys, CA 91406; Tel: 888-7071-1826, +1 (818) 222-9200, E-Mail: sales@oesincorp.com or visit the website at http://www.oesincorp.com

OES Logo
Visit OES Website
OES Facebook
OES Twitter
OES Videos

Motion Control – High Precision, Low Profile, Motorized Goniometer Stages Available from OES!

OES AK130 Motorized Goniometer Stage

OES Logo

Van Nuys, CA – — Motion Control – Optimal Engineering Systems, Inc. (OES) offers a very low cost, low profile solution for the precise measurement of angles or the rotation of an object to a precise angular position. The AK130-15 Goniometer Stage is just 2.362 in. (60 mm) high and the height of the center of rotation is 4.724in. (120 mm). The 4.724in. x 5.118 in. (120 mm x 130 mm) table has +/- 15o of rotation at speeds up to 10 o/sec, and features a precision ground worm gear with a 304:1 ratio and a resolution of 0.0005o with a 10 micro-step per step stepper motor driver; the stage is also available with a servo motor and optical encoder. This low profile goniometer stage is ideal for: Microscopy, crystallography, measurement of surgical cutting blades, laser positioning, light measurement, and inspection applications.

Critical measurement and inspection operations are assured because of the high precision worm gear and crossed roller guides, (Repeatability of +/- 3 arcsec, Accuracy of +/- 8 arcsec, and Backlash of +/- 3 arcsec). This compact black anodized Motorized Goniometer Stage measures just 12.952 in. (329 mm) long (including the standard 1.8o stepper motor by 5.118 in. (130 mm) wide and can handle loads to 33 lb (15 Kg) of load. Mounting holes on the stage and in the base assure easy integration into an application. A calibrated indicator displays the angle of rotation, a hand knob is provided for manual adjustment, and the stage can be ordered plug-and-play with a fully compatible controller from OES.

About OES – Optimal Engineering Systems, Inc. (OES) is a manufacturer of motion control products including: Stepper motor controllers and drivers, solenoid electronics, and positioning stages and slides. Applications include: Animation, automated assembly systems, automation, CNC machines, flight simulation, inspection systems, linear and rotary stages, machine tools, medical devices, motion control camera boom systems, optical comparators, CMMs, pan-tilt gimbals, PCB assembly & inspection, pick-and-place, positioning stages, robotics, scanners, security cameras, telescope drive mechanisms, time-lapse photography and winders.

Some of the industries OES serves are: Aerospace, Astronomy, Chemical, Communications, Educational Institutes, University, Colleges, Government Agencies, National Labs, Manufacturing, Medical, Metrology, Military, Motion Control, Museum, News Agencies, Semiconductor and Test Equipment. Optimal Engineering Systems, Inc’s. competitive advantage is its state-of-the-art in-house manufacturing facility in North America enabling OES to supply clients with custom designed orders or high volume just-in-time deliveries globally.

For additional information contact Customer Service at Optimal Engineering Systems, Inc. (OES) , 6901 Woodley Ave, Van Nuys, CA 91406; Tel: 888-7071-1826, +1 (818) 222-9200, E-Mail: sales@oesincorp.com or visit the website at http://www.oesincorp.com

OES Logo
Visit OES Website
OES Facebook
OES Twitter
OES Videos