Category Archives: Servo Motors

Motion Control – Linear Focus Actuator from Equipment Solutions Features 200 Nano Meters Repeatability!

Motion Control – 200 Nano Meters  Repeatability Actuator!

motion control - linear focus actuator


motion control - miniature components

 

Forestville, CA, – — Motion Control – This LFA-0604 Linear Focus Actuator: Flexture guidance system, 6 millimeter clear aperture, 4 millimeters of linear motion, 90 G’s acceleration (no load), 200 nanometers positioning repeatability, non-contact electro-optic position sensor, direct SCA814 Servo Controlled Amplifier compatibility, 38mm x 24mm, 80 grams

Motion Control – Application – Maxon Motors in Surgical Robots for Minimally Invasive Procedures!

Motion Control – Motors for Surgical Robots!

Motion control – The latest, next generation surgeries are being performed today using Intuitive Surgical Inc.’s (Sunnyvale, CA) da Vinci™S HD Surgical System, which allows surgeons to perform the most minimally invasive procedures to date. The system incorporates the height of motion control technologies so that every motion provides the smooth, accurate movements reminiscent of a skilled surgeon – even at slow, calculated speeds.

motion control - robot


motion control - maxon logo

 

Taunton, MA — Motion Control Products – The surgical system itself requires only the use of two 8- and one 12-mm wide hole in a patient, for insertion of the two surgical manipulators and a camera. Only the robot and surgical assistants stand over the patient, while the surgeon, the system operator, can be across the room at the Surgeon’s console where even the look and feel of the open surgery is duplicated with precision.

Motion Control – Electric Cylinder from Moticont Has Zero Cogging and High Throughput!

Motion Control – Electric Cylinder Has Zero Cogging

motion control - electric cylindermotion control - moticont

 

 

Van Nuys, CA — Motion Control – Moticont has added another non-commutated linear actuator to its DDLM series of low cost actuators.

The 0.125 in. (3.2 mm) diameter shaft has an internal thread on each end, a total of length of 4.960 in (126.0 mm), and extends 1.585 in. (40.3 mm) past the mounting end of the actuator. The shaft extends thru the 3/8-32 UNF x 0.250 (6.4 mm) long threaded studs at each end of the housing which can be used for mounting the DDL-019-070-01 linear actuator. Long life plain linear bearings support the internal shaft at both end of the actuator.

Miniature Linear Focus Actuator Features <50 Nanometer Positioning Resolution!

Motion Control – Miniature Linear Focus Actuator

motion control - linear focus actuator

Motion Control – LFA-1007 Linear Focus Actuator: 10mm clear aperture, 7mm range of motion, <50 nanometer positioning resolution, 50 grams moving mass, 70 x 70 x 50 (600g)

 

motion control - miniature components

 

 

Forestville, CA — Motion Control – Components – Linear Focus Actuator – The LFA-1007 is a high performance compact positioning actuator. It was specifically developed for applications requiring both high precision and high-speed positioning over a short to medium stroke. This product mates the voice coil motor to a perfectly smooth flexure guidance system and a very high resolution position feedback encoder.

Low Inertia, High Precision, Hollow Core Voice Coil Motors from Moticont!

Motion Control – Hollow Core Voice Coil Motor
motion control - voice coil motor


motion control - moticont

 

 

Van Nuys, CA – Motion Control Components -Low inertia hollow core voice coil or moving coil linear motors from Moticont feature high acceleration, precise positioning to less than one micron (0.00004 in.), high reliability, and low cost. The cleanroom friendly, non-commutated motors are available in 23 off-the-shelf standard sizes, Moticont hollow core voice coil linear motors have open apertures of 0.125 in. (3.2 mm) to 2.000 in. (50.8 mm).

Motion Control Application – Maxon Flat Motors Helps in Keeping Muscles in Shape!

Motion Control -Application – Flat Motors

Motion Control – For paraplegic people, rehabilitation is frequently a long process; this is why methods and tech-nology that optimize these measures for the patient are so important. At the Bern University of Applied Sciences, many years of research has led to the development of a recumbent trike with electrical stimulation. The patient’s movements are supported by a maxon flat motor.

motion control maxon application


motion control - maxon

 

Taunton, MA — Motion Control Products – Cycling with a recumbent trike can partially restore lost motor functions of patients with spinal cord lesions. Furthermore, it provides the patients with a very practical and successful basis for cardiopulmonary and muscular training units. The paralyzed leg muscles are reactivated by means of functional electric stimulation (FES) combined with controlled training.

Motion Control – Get Zero Cogging and High Throughput from Low Cost Moticont Linear Actuators!

Motion Control – Electric Cylinder!

motion control - electric cylinder


motion control - moticint

 

Van Nuys, CA — Moticont has introduced their highest force linear actuator in their DDLM Linear Actuator Series. The DDLM-038-051-01Linear Actuator is a low cost non-commutated linear actuator that is easily integrated into new and existing applications, and is the ideal choice when upgrading from a pneumatic system. Compact, clean, and quiet, this fully enclosed linear actuator, also referred to as an electric cylinder, is 1.500 in. (38.1 mm) in diameter with a housing length of 2.00 in. (50.4 mm) long.

Motion Control – ADVANCED Motion Controls 60Amp Micro-Sized FlexPro Servo Drives are available from Electromate!

Motion Control – Micro-Sized Servo Drives!

motion control - micro servo drive


motion control - electromate robotics

 

 

 

Vaughan, Ontario, Canada — Motion Control Components — ADVANCED Motion Controls has released 7 new micro-sized FlexPro servo drives rated to output 60A continuous. The 60A continuous current rating is 33% higher than previous models for the same size making these our highest power-density servo drives to date. This offering includes PCB Mount, Machine Embedded, and Development Board-factors.

Motion Control – Electromate extends its product portfolio to include Robots from Mecademic!

Motion Control – Electromate adds Robots from Mecademic!

motion control - electromate robotics

Electromate’s new partnership with Mecademic will expand its reach to end users and manufacturers needing ultra compact and precise industrial robots across Canada.

 

 

 

TORONTO, Ontario — Electromate Inc., a leading Canadian Distributor of Precision Robotic & Mechatronic Solutions, today announced a partnership with Mecademic, a Montreal based premier manufacturer of the world’s smallest, most compact, and precise industrial robots.

Motion Control – Moticont Adds 1 Inch Stroke, Direct Drive Linear Actuator to Their Patented SDLM Series of Electric Cylinders!

Motion Control –  Electric Cylinders!

motion control - electric Cylinder


motion control - moticont
Van Nuys, CA — Motion Control – The SDLM Series of Electric Cylinders from Moticont now includes a 1.0 inch (25.4 mm) stroke actuator in their compact 0.750 in. (19.1 mm) diameter series of linear actuators. The new SDLM-019-095-01-01 actuator features a continuous force of 6.8 oz (1.9 N) and a peak force of 21.6 oz (6.0 N). A precision linear optical quadrature encoder is integrated and protected inside the actuator housing.

Motion Control – Compact Direct Drive Linear Actuator Has Integrated Encoder and Temperature Sensor for Increased Throughput!

Motion Control – Electric Cylinder has Increased Throughput!

 

motion control - electric cylinder

motion control - moticont
Van Nuys, CA — The Compact SDLM-051-070-01-01 Direct Drive Linear Actuator with integrated position and temperature sensors is the latest addition to the patented series of zero backlash, zero cogging, high acceleration, high speed, high resolution, long life actuators from Moticont. This direct drive linear Actuator, also referred to as an Electric Cylinder is 2.000 in. (50.9 mm) in diameter and the compact housing length is just 2.750 in (69.9 mm).

Motion Control Products – 0.5 Inch Stroke Voice Coil Motor Features High Force to Size Ratio!

Motion Control Products – Voice Coil Linear Actuator

 

MotiCont-Logo

Van Nuys, CA – Motion Control Products – Moticont’s GVCM-051-025-01 Linear Voice Coil Motor features: High acceleration/deceleration, high speed, high reliability, zero backlash, high accuracy, high repeatability, and a 0.5 inch (12.7 mm) stroke length! Also referred to as an Electric Cylinder, this linear actuator is an ideal low cost, high accuracy replacement for hydraulic and pneumatic linear actuators. This clean, compact, voice coil motor has a high force to size ratio with 5.3 lbs (23.5 N) continuous force and 16.7 lb (74.4 N) of peak force at 10% duty cycle with a housing measuring just 2.00 in. (50.8 mm) dia. x 1.00 in. (25.4 mm) long.

The precision ground 0.1572 (3.993 mm) diameter shaft has an internal thread, and the housing has threaded mounting holes on each end for easy integration into current and future applications. This clean, quiet, efficient, low inertia, brushless actuator featuring an internal shaft and recirculating ball bearing is ideal for: Medical devices, antenna positioning, testing, sorting, assembly equipment, work holding and clamping, scanners and laser beam steering and filtering, laser machining and drilling, wafer handling, optical focusing, and dynamic vibration absorption,. The Moticont’s GVCM-051-025-01 linear voice coil motor can also be ordered as a complete plug-and-play system including a position sensor, and controller.

There are currently 7 series of Moticont’s GVCM motors based on diameter of the motor, and models based on length of stroke and/or force to select from with additional motors being added to select from. To find the right motor for you application go to: http://moticont.com/linear-motor-with-bearing.htm

About Moticont – Moticont is a manufacturer of motion control products. Their product line includes voice coil motors, three phase brushless motors and positioning stages and slides.

Moticont is committed to exceeding Our customers’ quality expectations and industry standards throughout the design, manufacturing, service and technical support phases. Our modern manufacturing facility, highly controlled processes, committed staff, and extensive testing complement our product design strengths. This enables us to supply our clients with specialized small orders to high volume just-in-time deliveries.

We offer an extensive line of standard products ready to be shipped immediately from stock, and when standard products are not quite right for an application, highly trained design engineers are always available to develop custom motion control products to fit the specific needs or our customers.

For additional information contact Sales Team at Moticont, 6901 Woodley Ave, Van Nuys, CA 91406; Toll Free: +1 (888) 785-1804, Tel: +1 (818) 785-1800, moticont@moticont.comor visit the website at http://www.moticont.com

See this and other Motion Control Components from Moticont featured on:
http://MotionShop.com
http://AllMotionBlogger.com
http://Automation-Blogger.com
http://MotionControlBlogger.com
http://MotionControlWeb.com
http://MotionShop.net

http://Catalogs-MotionControl.com

 

MotiCont-Logo
Visit our Website
Other Products
Videos

New VLM Servo Motors for value conscious applications!

motion control Kollmorgen Servo Motor

 

Servo2Go-Logo

 

 

Greenville, DE —-Motion Control Components – Kollmorgen has launched the VLM servo motor series to fill the gap between stepper and high-performance servo motors. The new VLM series synchronous servo motors offer OEMs, machine builders and end-users, an excellent price-performance proposition in the torque range of 0.5 to 4.5 Nm continuous and 16 Nm peak, with speeds of up to 6000 rpm. They also provide highly flexible configuration, proven quality and high reliability. Hence, they are a very useful solution for many applications where stepper or asynchronous motors are pushed to their limits but the expense and unused dynamics of high performance servo motors is not desirable.

The many standard design and configuration options built into the range allow engineers an optimal solution from the outset, to tailor their applications and machine requirements. Thus, installation time and cost is minimized and the price-performance ratio is further improved. The VLM series motors are available with standard frame sizes of 60 mm and 90-mm or NEMA 23 and 34 in each of the six most popular motor sizes and with a choice of twelve standard windings. The extensive possibilities for shaft and mounting facilitate seamless integration into virtually any system.

Feedback options include Digital Resolver (SFD), resolver, encoder and Hall sensors. VLM motors achieve continuous torque up to 4.5 Nm and peak torque to 16 Nm and can be used in power systems with 230 VAC. And of course, the new motors meet the ROHS Directives for CE and UL certification.

Information on the Kollmorgen VLM Brushless Servo Motors available from Servo2Go.com can be viewed at: https://www.servo2go.com/products/servo-motors-drives/servo-motors/ http://www.servo2go.com/product.php?ID=101027&cat=

These and other Motion Control Products are available through www.Servo2Go.com

For further information on this new product or others in our extensive product portfolio, call 1- 877-378-0240 or e-mail Warren Osak atwarren@servo2go.com or visit Servo2Go.com at: www.Servo2Go.com

For other Motion Control Components, Applications, and Technology from OES (Optimal Engineering Systems) go to: http://MotionControlWeb.com

Servo2Go-Logo
Visit our Website
Twitter Link
Facebook Link

Motion Control Application – Intelligent robot systems are increasingly being used in disaster control, rescue missions and salvage operations!

After the severe earthquake in Japan and the subsequent nuclear disaster in Fukushima, Quince managed to reach the upper floors of the ruins of the power plant. There it measured the radioactivity levels and sent HD images to the world outside.

Wherever it is too dangerous for humans. Robots that can look for survivors after an explosion, an earthquake or other natural disasters, providing humans with a view of inaccessible areas. Powerful EC motors from maxon motor give the Japanese rescue robot “Quince” its drive.motion control application robot Quince

 

Maxon Logo

Fall River, MA — Motion Control Components Application – Robots that are used in disaster areas have to have a very high level of adaptability. They have to be fairly small, not too heavy and maneuverable enough to get through cracks or narrow spaces to reach areas deep inside a building. Furthermore rough terrain should present no problem. These rescue robots enter and explore buildings to determine if there are gases, radiation or other life-threatening hazards, before human rescue teams can search the area. Quince has proven that it fulfills all these demands. After the severe earthquake in Japan and the subsequent nuclear disaster in Fukushima, Quince managed to reach the upper floors of the ruins of the power plant in June 2011. There it measured the radioactivity levels and sent HD images to the world outside (To see video – CLICK HERE). The robot was able to supply valuable information from areas where no human can set foot.motion control robot goes down stairs

Quince weighs 27 kg and is equipped with four moving caterpillar drives (flippers). These flippers automatically adapt their angular position to the surface underneath – regardless of whether the robot is climbing steep stairs or crossing rough terrain. Correct ground contact is a very important prerequisite. This contact is accurately analyzed by measuring the power consumption of the flipper motors. Furthermore PSD (Position-Sensitive Device) sensors on the front and rear flippers measure the distance to the ground. In addition to a gripper arm (see fig. 2), two laser scanners can also be attached to the robot. These scanners are capable of accurately capturing the structure of the terrain.motion control robot navigates rough terrain

Additionally Quince is equipped with a “bird’s eye camera” and can travel quite fast, at 1.6 meters per second. The operator that controls the robot has to tell it which direction to take, but the robot itself determines the optimal flipper positions for crossing various surfaces, for example stairs. Newer Quince motors have additionally been equipped with a device for collecting radio-active dust or ultra-fine particles, as well as a 3D scanner. To ensure that no robot is lost, a connection to a wireless network is possible, which is the only way to navigate the robot if the connection cable breaks.

The rescue robot was developed by Eiji Koyanagi, Vice-Director of the Chiba Institute of Technology Future Robotics Technology Center (fuRO). Koyanagi started his career as a teacher – at the age of 51, he became a professor. This means that he has a completely different background than other researchers in the field of robotics. Quince has been specially designed for extreme conditions in environments where it would be too dangerous for humans. Therefore its main area of application is disaster areas. “When you develop a robot, you first have to consider the tasks that it will perform later. That is the biggest challenge,” explains Koyanagi. Hitherto eight Quince robots have been built. But before this could be done, all components had to be 100% functional. To this end, various trials were run in the large “Disaster City” training area in College Station, Texas. Quince was the only robot that successfully completed the entire obstacle course at the site as part of a RoboCup contest. In preparation for using the robot inside the Fukushima Daiichi nuclear power plant, several specific customizations were required. “The conditions in the nuclear reactor buildings are very tough. If we had attempted to send Quince in without modifications, it would probably have met its end,” says Koyanagi. Therefore the robot had to be able to survive a fall from approx. 2 m high unscathed, and had to be largely maintenance-free.

Powerful motors to beat every obstacle

Motion Control -Maxon Motors used in robot Quince

Where the motor selection was concerned, fuRO required absolutely reliable drives. The motors have to provide high power and high efficiency, yet be small and light. These requirements were precisely met by maxon motors, explains Koyanagi. Six powerful maxon motors drive the robot. The brushless EC-4pole 30 direct current motors each provide 200 W; two of these have been installed in the two main chains. The powerful 4-pole units give their all when Quince maneuvers its way across uneven terrain. Four additional motors (EC22) drive the moving chain drives (flippers). These can automatically adapt their angular position to the surface below. The 3D scanner unit of Quince is moved to the right position by an RE-max 24. Thanks to the special winding technology and the 4-pole magnets, the maxon EC-4pole drives are unbeatable when it comes to delivering the highest driving power per unit of volume and weight. The motors have no cogging torque, high efficiency, and excellent control dynamics. The metal housing additionally ensures good heat dissipation and mechanical stability. All motors of the chain drives have been combined with the GP32HP (High Power) planetary gearhead with MR encoder. This gearhead was customized by installing a large ball bearing and a reinforced motor shaft. With this power pack, Quince has no trouble managing almost any obstacle.

Contact maxon for more details info@maxonmotorusa.com

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

Maxon Logo
Visit our Website
Order Our Catalog

Motion Control – Complete Guided Motion Solutions from A to X-Y-Z … … Available from Electromate!

Motion Control – Linear Systems

motion control - linear systems

motion control - electromate- robotics

 

 

Vaughan, Ontario, Canada — Motion Control Components — Bishop-Wisecarver invented and patented DualVee Motion Technology® more than 40 years ago to provide a solution for harsh environment applications where existing technologies were ineffective. DualVee® also proved excellent for long length, smooth motion and low noise requirements.

Motion Control – Customer Driven AC Servo Design

The mid-level, general-purpose 1S Series Servos incorporate valuable input from our customers to optimize use from design to commissioning.

Lower Costs and Total Cost of Ownership
The 1S Series eliminates up to 20% of hidden servo system costs to the customer by no longer requiring separate external parts such as servodrive controller cable, terminal block for I/O, safety cable, brake relay and absolute encoder battery and cable.  Regardless of power rating, all 1S power drives have a uniform height to simplify design and improve control cabinet air circulation. We streamlined I/O connection, replacing an external terminal and cable with a pluggable connector with push-in terminals that allows wiring to be prepared separately. In the process, we increased the number and mix of supported I/O.  The end user benefits from lower maintenance costs.

Advances for High Accuracy Machines
The 1S servomotors use a gear-less/battery-less, multi-turn 23-bit absolute encoder, 16-bit multi-turn to provide accurate position input. Advanced tuning functions help shorten settling time, allowing faster production speeds and greater throughput.
Expanded Built-in Safety Capability

Machine safety for rotating hazards takes a prominent position in equipment design since the recent changes in injury liability. To help OEMs simplify safety system design and standardize on one series without stocking many separate drives, the 1S Series servodrives offer both networked and hardwired safe torque off built in. Configuration of FailSafe over EtherCAT (FSoE) only requires connecting NX Series safety control units to 1S Series servos  via open network “EtherCAT”. No wiring is required for the emergency stop of each axis for servo.
First Wave of 1S Servos

The first wave satisfies 100 W to 3 kW applications. Future releases will address power requirements of higher and lower power ratings.

To Down Load the 1S Series AC Servo System Catalog CLICK HERE

To view YouTube Video CLICK HERE

For additional on the 1S Series AC Servo System CLICK HERE

To subscribe to OMRON Newsletters CLICK HERE

To contact OMRON about this or other industrial products CLICK HERE

KEEP YOUR WORKPLACE SAFE! – GET A ‘GOTCHA-STICK” CLICK HERE

Motion Control – High Acceleration, High Precision, Brushless Linear Motors from Moticont!

Motion Control - Moticont-brushless-linear-motors-lbim-021

Van Nuys, CA – Motion Control Components – The off-the-shelf, LBIM-021 Series of Linear Three-phase Brushless Servo Motors from Moticont are sized to fit a broad range of linear motion applications. These low cost, compact linear motors feature: High acceleration, high speed, high accuracy, high repeatability, and high precision to less than one micron (0.00004 in.). The LBIM-021 Linear motor series is comprised of four sizes of forcers (the moving part of a linear motor) and matching magnetic tracks creating forces of 8.7 lbs (38.7 N), 16.3 lbs (72.4 N), 23.1 lbs (102.9 N), and 31.0 lbs (138.1 N) at 10% duty cycle. The light weight ironless forcers have no iron providing high acceleration, low inertia, and cog free motion. These high speed, non-contact brushless linear motors are ideal for a variety of: Medical, manufacturing, scanning, inspection, laser cutting, and precision assembly applications.

MotiCont-Logo

Clean room and people friendly, these clean, non-commutated, quiet linear servo motors are easily integrated into new and existing applications. Modular magnetic tracks, available in four standard and custom lengths, can be assembled to create unlimited stroke lengths, additionally; multiple forcers can operate in the same magnetic track with overlapping travels. LBIM-021 Series Linear Servo Motors can be commutated in a trapezoidal or sinusoidal mode and can be ordered as complete plug-and-play systems, including, position sensors, controllers, amplifiers, and power supplies. Other sizes of linear motors and custom designs are also available from Moticont.

About Moticont – Moticont is a manufacturer of motion control products. Their product line includes voice coil motors, three phase brushless motors and positioning stages and slides.

Moticont is committed to exceeding their customers’ quality expectations and industry standards throughout the design, manufacturing, service and technical support phases. Our modern manufacturing facility, highly controlled processes, committed staff, and extensive testing complement our product design strengths. This enables us to supply our clients with specialized small orders to high volume just-in-time deliveries.

We offer an extensive line of standard products ready to be shipped immediately from stock, and when standard products are not quite right for an application, highly trained design engineers are always available to develop custom motion control products to fit the specific needs or our customers.

For additional information contact Moticont, “A Motion Company” at 6901 Woodley Avenue, Van Nuys, CA 91406, USA; Tel: (888) 785-1804, Fax: (818) 785-5713, E-Mail: moticont@moticont.com or visit the website at http://www.moticont.com

MotiCont-Logo
Visit our Website
Other Products
Videos

Motion Control – High Torque AC Servo Motors from JVL

Motion Control – Consider These High Torque, AC Servo Motors: MSE400, MSE800, MSE1K5, and MSE3K0 from JVL!

Motion Control MAC 402 is DC version of MAC 400 from JVL

JVL Logo

 

Birkerød, Denmark and Morrow, OH (USA) — Motion Control – The AC Servo Motors MSE400, MSE800, MSE1K5 and MSE3K0 have been designed by JVL for use with the JVL AMC20 series of advanced AC Servo Controllers.

 

 

Features Include

  • Highest torque density rating in the industry
  • High torque-to-inertia for faster start and stop
  • Rugged design and long life bearings
  • High power, cooler running, rare-earth magnet design
  • Exposed-laminated housing, optimized for high torque and smooth operation
  • Encoder 2000p/r.
  • With JVL AMC20 series servo motor controller, 8000 counts/r with index pulse
  • Very short length compared to power rating: 750W@102mm
  • Standard servo flange
  • Yaskawa/Omron flange and shaft
  • High Axial and radial shaft load
  • Low noise
  • Option for planetary gear head
  • Option for 24VDC brake

Motion Control MAC 402 is DC version of MAC 400 from JVL

–Complete specifications and detailed drawings of the AC Servos Are Available Here!

About JVL – JVL is recognized as a leader for its development of modern, compact stepper motor drivers and VAC and VDC controllers as well as MAC motor series of integrated VAC servo motors (up to 3000W), and the QuickStep integrated stepper motors (up to 25Nm). Both the servo motor and stepper motor series includes the controller and encoder integrated into one compact unit.

JVL with more than 20 years of motion control experience enjoys a reputation for the development of specialized, customized equipment. They work together with their customers and representatives to find an economic, yet technically advanced solution to complicated control applications.

JVL’s wide selection of quality products for motion control components include: Integrated VAC Servo motors, Integrated Stepper motors, VAC Servo motor controllers, VDC Servo motor controllers, Motor drivers (Stepper, VAC and VDC), Keyboard/Display (Input/Output- and Counter Modules).

JVL USA • Att: Mike Fisher • National Sales Manager
8610 Morrow-Rossburg Rd • Morrow • OH 45152-9444
E-mail: mfisher@jvlusa.com • Tel.: 513/877-3134 •Tel.: 513/282-0888 (Tech Support Line) •
Fax: 513/877-2471•
For Additional Information about Mike Fisher and JVL USA – Click Here

 

USA and Canada – Reps & Distributors: – Click Here

 

All Other Countries:

Further information can be obtained from:

JVL Industri Elektronik A/S

Blorkken 42, DK 3460, Birkerød, Denmark

E-mail: jvj@jvl.dk Tel.: +45 4582 4440 ; Fax.: +45 4582 5550 ;

For JVL Home Office and World Wide Directory of Reps & Distributors Click Here

JVL Logo
Visit our Website
Order Our Catalog
Request Newsletter
JVL-Trade Fairs
Twitter Link
Facebook Link

Motion Control – 4 Pole Motor for Demanding Operating Room Applications from Maxon!

The Sterilizable EC-4Pole 30 from Maxon Motor, A Brushless DC Motor for Demanding Operating Room Applications!

Maxon’s new brushless electric motor, the EC-4pole 30, delivers high torque (106 mNm) and is sterilizable, a perfect drive for hand-held surgical tools.

Maxon motion control EC-4Pole motor for medical applications

Maxon Logo

 

Fall River, MA — Automation Motion Control — Swiss drive specialist maxon motor has developed a robust brushless DC motor for hand-held surgical tools: the EC-4pole 30. Featuring two pole pairs, this DC motor provides a nominal torque of 106 mNm and an output of 150 W. It has a hermetically sealed rotor, meaning that it can withstand over 1000 autoclave cycles.

Need to operate at overload? No problem!

The EC-4pole 30 is equipped with the special ironless maxon winding, which makes it highly efficient. Another key feature is that the torque and current behave linearly and the drive can be overloaded. It is available with an optional Hall sensor, as well as with a hollow shaft with a diameter of up to 4.1 millimeters. With the EC-4pole 30, engineers get a first-class drive for surgical hand tools that work flawlessly under the tough conditions of operating rooms.

Maxon offers a complete line of dc motors, gearheads and controllers. Contact us to help find the right solution for your application.info@maxonmotor.com

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website atwww.maxonmotor.com.

Maxon Logo
Visit our Website
Order Our Catalog