Category Archives: Motors – Steppers

Motion Control – Maxon introduces a multi-axis controller for highly dynamic positioning tasks!

Motion Control – Miniature Multi-axis Controller

Maxon is launching the next generation of Motion Controllers with its MiniMACS6-AMP-4/50/10. The controller is ideal for use in applications where PLC solutions may be too expensive or cannot meet customer-specific requirements.

motion control - miniature controller

Taunton, MA — Motion Control Products – Maxon’s new multi-axis controller, the MiniMACS6-AMP-4/50/10, offers precise and highly dynamic control of up to six brushed DC motors or four brushless DC motors (up to 540 W continuous output power and 1.6 kW peak output power).

motion control - maxon motors

 

 

The controller is an economical and compact solution for system designers who develop autonomous robots or shuttle systems

A significant advantage of the new multi-axis solution is that it is programmable with the comprehensive ApossIDE automation software and the license-free Motion Control Library (written in C). Integrated bus interfaces enable efficient data exchange with higher-level controllers; however, it is also possible to run complete process sequences autonomously, without a PLC or PC. The MiniMACS6-AMP-4/50/10 will be available in early 2021.

Motion Control – Low Profile XY Brushless Linear Motor Positioning Stage from H2W Technologies

Motion Control – Low Profile XY Linear Motor Positioning Stage

motion control - custom stages


motion control - h2wSanta Clarita, CA —– Motion Control – The
SRS-004-006/004-003-01-XY is a low profile XY single rail positioning stage that uses brushless linear motors to generate a continuous/peak force of 6.2 lbs [27.8 N]/18.7 lbs [83.3 N] (bottom axis), 3.1 lbs [13.8 N]/9.4 lbs [41.8 N] (top axis), with a total stroke length of 4.3 in [109 mm] (bottom axis), 4.3 in [109 mm] (top axis). The top axis is able to directly mount to the moving bottom axis motor. This helps reduce the overall height and moving mass of the system.

Motion Control – Electromate Recognized with 2021 AHTD Foundation Award!

Motion Control – Electromate 2021 AHTD Foundation Award!

motion control - electromate components


motion control - electromateToronto, Ontario – June 18, 2021 – Electromate received a Foundation Award from the Association for High Technology Distribution (AHTD), recognizing the company’s 25 years of membership and support. This is the first year the Award has been given, honoring a small group of members out of approximately 300 automation solution providers and manufacturers.

The AHTD is dedicated to maximizing the productivity, growth, and enterprise opportunities of its high-tech automation solution provider and manufacturer members. These goals align with Electromate’s commitment to driving innovation, identifying emerging technologies and products, promoting the education of automation and motion control, and fostering its relationships with industry peers.

Motion Control – 20 mm Linear Stepper Motor by Nippon Pulse are available from Electromate!

Motion Control  – 20 mm Linear Stepper Motor!

motion control - linear stepper

motion control - electromate

 

 

Vaughan, Ontario, Canada — Motion Control Components — Nippon Pulse is excited to introduce its smallest linear stepper motor yet, the PFL20 Linearstep. The PFL20 is a highly efficient, high thrust tin-can linear actuator with a 20mm diameter and a bipolar winding.

PFL20 is RoHS-compliant, has a 30/60mm effective stroke, and can reach 6 N of force at 200 pps. With 24 steps per revolution, the lead screw has a 1.2mm thread pitch; the PFL20 also reaches 5V rated voltage, resistance of 33 Ohms/phase and inductance of 12mH/phase. The datasheet with additional specifications can be found here.

Motion Control – COVID-19 … Important Information for Ventilator Manufacturers!

Motion Control – ATTENTION – Ventilator Manufacturers!

motion control - ventilator components

 

motion control - electromate

 

 

Vaughan, Ontario, Canada — Motion Control Components — COVID-19 has caused a significant shortage of ventilators for the most seriously ill patients. We are facing a global shortage of equipment and have precious little time to respond.

Electromate is a mechanical ventilator component supplier and works with a number of manufacturing partners that supply crucial components needed to build more ventilators.

These include:

  • HMI’s
  • Linear guides
  • Linear actuators
  • Screw assemblies
  • Compact gearboxes
  • High efficiency servo & stepper motors
  • Programmable motion controllers and drives

Our team of motion design experts are located all across Canada and are available right now to help you with any electro-mechanical ventilator design. If you are working on a ventilator involving rotary, linear, or any other motion, we will provide immediate help with electro-mechanical engineering and component sourcing. Contact us today.

We are already working with ventilator and respirator companies and encourage any other businesses working on COVID-19 solutions to reach out to us.

All inquiries regarding ventilator components or any other equipment to help battle COVID-19 are given utmost priority. We can help to optimize your design quickly and provide fast turnaround proposals as requested. Additionally, we are able to meet high production demands in a very short time by utlilizing ‘Medical Fast Track Programs’ -info.us@maxongroup.com from maxon, and other vendors.

Many of the products we sell to the medical technology sector have ISO 13485 certification. This certification confirms that these products adhere to the fundamental requirements of medical technology and that all processes and procedures are documented, thereby guaranteeing traceability.

In addition to helping with the design and acquisition of critical components used in ventilators and respirators, we also want to make you aware of initiatives that you may be able to utilize. Please read below to learn more about these programs and how you can assist with the COVID-19 cause.

CODE LIFE VENTILATOR CHALLANGE

The Montreal General Hospital Foundation, in collaboration with the Research Institute of the McGill University Health Centre (RI-MUHC), is launching a global innovation challenge, backed by a prize of $200,000 CAD. They are calling for teams to design a simple, low-cost, easy-to-manufacture and easy-to-maintain ventilator which could be deployed anywhere needed to save lives.

To learn more, please visit https://www.mghfoundation.com/en/news/code-life-ventilator-challenge/

 

 

MIT EMERGENCY VENTILATOR (E-VENT) PROJECT COPY

MIT has launched an emergency research project with a team of Engineers and American clinicians to address the question:

Is it possible to safely ventilate a COVID-19 patient by automatically actuating a manual resuscitator?

Their process in approaching this question is to first identify the minimum requirements for a low-cost ventilator, based on the collective wisdom of many clinicians, design against these requirements, conduct immediate testing, report the results, iterate and facilitate discussion.

motion control - electromate

To learn more, please visit https://e-vent.mit.edu/

 

 

About Electromate:

Electromate’s Core Purpose is to help Manufacturers build better machines using differentiated automation technology. They specialize in Robotic and Mechatronic Solutions for the Industrial Automation marketplace. Respected by customers as a premiere source for High Performance Automation and Motion Control Components & Systems, Electromate® specializes in AC & DC Servo and Stepper Motors & Drives, Motion & Automation Controllers, Positioning Systems & Actuators, Feedback Devices, Gearing Products and HMI’s & Operator Displays, all supported via extensive product selection, just-in-timedelivery, dedicated customer service and technical engineering support.

More on Electromate can be found at

Website: http://www.electromate.com

LinkedIn: https://www.linkedin.com/company-beta/209277/

Twitter: https://twitter.com/Electromate

Facebook: https://www.facebook.com/electromateindustrial/

Blog: https://electromate.wordpress.com/

motion control - electromate

For more information on the “Best Place to Work”CLICK HERE!

To view Electromate’s new corporate video CLICK HERE

 

For further information on this new product or others in our extensive product portfolio, call 1-877-SERVO99 (737-8699) or e-mail Warren Osak at sales@electromate.com or visit Electromate at: www.electromate.com


See this and other Motion Control Components from Electromate featured on:

http://MotionShop.com

http://AllMotionBlogger.com

http://Automation-Blogger.com

http://MotionControlBlogger.com

http://motioncontrolBuyersGuide.com

http://MotionControlWeb.com

http://MotionShop.net

http://Catalogs-MotionControl.com

http://MotionControlMarketing.com

http://Gotcha-Stick.com

motion control - electromate logo

Motion Control ServoStep Integrated Stepper Motor in size NEMA 17, torque up to 0.8 Nm!

Motion Control Integrated Step Motors

motion control integrated stepper motor

Motion Control - Electromate-Logo

 

Vaughan, Ontario, Canada — Motion Control Components — JVL Industri Elektronik A/S, one of the world leaders in the field of integrated servo – and stepper motors introduces a new compact and slim stepper motor. The new ServoStep integrated stepper motor series MIS171 to MIS176 have a NEMA 17 42×42 mm flange and include controller with 6 different industrial Ethernet protocols, absolute multiturn encoder, closed loop and M12 connectors. This new motor family is based on the latest microprocessor and cooling technology and an advancement compared to previous designs.

All the necessary electronics in a stepper system are integrated in the motor itself and are similar to the concept used by other JVL motors, making it very easy to use in all kind of motion control stepper or servomotor applications. The motor contains everything needed to solve a modern control task, either as a stand-alone with own easy programmable motion controller or controlled from an external PLC or PC. 8 I/O points can be individually configured as digital input, digital output or analogue input. Modbus RTU or CANopen provide easy connections to a PLC or HMI. An ActiveX/OCX driver is available to make simple interface to LabView, Excel, VB or other Windows-programs. Up to 254 axis can be connected on the same RS485 bus.

Key features:
  • Industrial Ethernet. 6 Protocols 
  • Very high motor power and torque
  • Closed-loop operation with current control 
  • Absolute multiturn encoder
  • Safe Torque Off (STO) input
  • High resolution 409600 cnt/rev.
  • Speed 0-3000 in 0.01RPM steps
  • Wide supply range 7-72 VDC
  • Protection class up to IP67
  • M12 or M23 connectors
Motion Control Industrial Ethernet: 

Profinet, EtherCAT, Powerlink, EtherNet/IP, Modbus TCP or SERCOS III are available and for EtherCAT and SERCOS III synchronization and drive profiles are available. MACtalk can use Ethernet for commissioning the motor so no need for RS232/RS485 converter or additional cables. The motor has the ability to be upgraded with other protocols or newer versions of the same protocol at any time Because of the upgradeability, the JVL Industrial Ethernet module is also ‘future proof' as newer versions of the protocols will always fit into the design. The motor is equipped with two Ethernet connectors and a built-in switch, enabling line topology without any extra expensive hardware. Several LEDs, enabling technicians and operators to get a quick status overview.

Motion Control Motor range:
  • MIS171 with 0,15 Nm, length 70,5 mm. 5mm shaft 
  • MIS173 with 0,26 Nm, length 83,5 mm. 5 or 6,35mm shaft
  • MIS176 with 0,80 Nm, length 104,3 mm. 8 mm shaft

The motors can be operated as stand-alone units or controlled from a PLC or PC. The 8 I/Os can be individually configured as digital input, digital output or analog input. As standard, it is possible to communicate with holistic systems via for example Modbus RTU or CANopen. The MAC motor standard protocol that is also supported makes it possible to connect up to 254 other JVL integrated motors. The MIS17 series allows connectivity to all industrial Ethernet interfaces such as Profinet, EtherCAT, Powerlink, EtherNet/IP, Modbus TCP and SERCOS III.

Motion Control Interface: 
  • Industrial Ethernets Profinet, EtherCAT, Powerlink, EtherNet/IP, Modbus TCP and SERCOS III
  • CANopen DSP402 and DS301
  • Pulse/Direction mode for electronic gear
  • High speed position capture
  • ActiveX/OCX driver as well as JVL MacTalk Protocol
  • Strong graphic programming with + – * / calculations and advanced features
  • SSI interface for external linear or rotary absolute encoders
  • External encoder for dual closed-loop. 
  • RS485 up to 921 kbit and Modbus RTU
  • RS422 and RS485 for encoder I/O and connection to external HMI, PLC or encoder
  • Point-to-point or multi-axis operation with up to 254 JVL motors on the same RS485 bus
  • Wireless Industrial Ethernet through Bluetooth or WLAN
Motion Control Motor specification: 
  • Built-in PLC with 8 DIO, 24V or 0-5V (12bit) analog input with advanced filtering
  • Speed-precision 0.01 RPM. Acceleration-precision 1 RPM / sec.
  • Absolute multi-turn encoder
  • Built-in encoder for closed loop and stall detection and control 
  • Wide supply range of 7-72 VDC provides high torque at high speeds
  • Dual supply maintain position values etc. in emergency situations
  • Motor current 0-4 Amp RMS and 5,6 Amp peak
  • Closed-Loop operation
  • Double shaft and brake option
  • All connections with M12 connectors in IP67
  • Top or rear-end mounted M12 or M23 hybrid connector

For further information on the JVL ServoStep Series Motors, call 1-877-SERVO99 (737-8699) or e-mail Warren Osak at sales@electromate.com or visit Electromate at: www.electromate.com

About Electromate:

Electromate’s Core Purpose is to help Manufacturers build better machines using differentiated automation technology. They specialize in Robotic and Mechatronic Solutions for the Industrial Automation marketplace. Respected by customers as a premiere source for High Performance Automation and Motion Control Components & Systems, Electromate® specializes in AC & DC Servo and Stepper Motors & Drives, Motion & Automation Controllers, Positioning Systems & Actuators, Feedback Devices, Gearing Products and HMI’s & Operator Displays, all supported via extensive product selection, just-in-timedelivery, dedicated customer service and technical engineering support.

More on Electromate can be found at

Website: http://www.electromate.com

LinkedIn: https://www.linkedin.com/company-beta/209277/

Twitter: https://twitter.com/Electromate

Facebook: https://www.facebook.com/electromateindustrial/

Google+: https://plus.google.com/104057418684128701566

Blog: https://electromate.wordpress.com/

Electromate Best Blace to Work

For more information on the “Best Place to Work”CLICK HERE!

To view Electromate’s new corporate video CLICK HERE

To see all of Electromate’s Products and Application Stories featured on MotionShop.com, enter electromate in the Google custom search box (upper left, above)

For further information on this new product or others in our extensive product portfolio, call 1-877-SERVO99 (737-8699) or e-mail Warren Osak at sales@electromate.com or visit Electromate at: www.electromate.com

Motion Control - Electromate-Logo
Visit our Website
Motion Control - Electromate Twitter Link
Motion Control - Electromate Facebook Link

Motion Control – Maxon Opens Manufacturing Facility in Taunton, Massachusetts!

New Facility Expands Maxon’s Operations & Capabilities to Service US Customers.

 

Maxon Logo

 

 

 

Taunton, MA – Maxon precision motors, a division of maxon motor of Sachsein, Switzerland, has announced the opening of a new manufacturing facility in Taunton, MA. The two-story, 59,000 sq. foot facility is located within the Myles Standish Business Park in Taunton at 125 Dever Drive.

Company officials led by Chris Blake, mpm President welcomed state/local officials and invited guests to a grand opening event at the facility this morning which included a ribbon cutting ceremony and tours of the building.

The new building will provide design engineering and production operations, significantly advancing maxon precision motors presence and capabilities in North America. Its opening is an integral component in an ongoing global growth strategy underway by the privately owned Swiss company, in business since 1961.

maxon motor is the leading provider of precision DC motors and drive technology with distribution and sales in 40 countries worldwide. maxon’s products include brushed and brushless DC motors, gearheads, sensors/encoders and customized drives. Its highly engineered products are used in a wide range of industries and applications including medical technology, industrial automation, robotics, security and communications, aerospace, automotive, and measurement/testing.

The new facility replaces a former sales/distribution and assembly operation at 101 Waldron Road in Fall River, MA, and will significantly expand maxon precision motors capabilities and employment. USA customers will benefit from closer collaboration that will provide value added opportunities with faster turnaround. Plus, a localized supply chain with domestic vendors will help build stronger customer relationships while reducing lead times.

“Our vision is to be an integral part of maxon’s global growth strategy,” explained Mr. Blake, who heads up the US management team. “With expanded engineering services in place, our customers will enjoy a closer collaboration on design and manufacturing and have a more direct line to our team during concept development, which will include rapid prototyping to better execute customer-specific products.”

The new Taunton facility will include offices and conference areas, space for warehousing, and significant manufacturing space. PIt will integrate engineering with true high-volume manufacturing capabilities.

About maxon motor maxon motor is a developer and manufacturer of brushed and brushless DC motors, as well as gearheads, encoders, controllers, and entire mechatronic systems. maxon drives are used wherever requirements are particularly high: in NASA’s Mars rovers, in surgical power tools, in humanoid robots, and in precision industrial applications, for example. To maintain its leadership in this demanding market, the company invests a considerable share of its annual revenue in research and development. Worldwide, maxon employs some 2,600 workers at eight production sites and is represented by sales companies in more than 30 countries. www.maxonmotor.com

For More Information Contact: Debora Setters, National Marketing Manager, maxon precision motors, inc. Taunton, MA, dsetters@maxonmotorusa.com/508-916-6602

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

Maxon Handbook Banner

Maxon Logo
Visit our Website
Order Our Catalog

 

 

 

 

For other Motion Control Components, Applications, and Technology from Maxon Motor visit: http://motioncontrolweb.com

New VLM Servo Motors for value conscious applications!

motion control Kollmorgen Servo Motor

 

Servo2Go-Logo

 

 

Greenville, DE —-Motion Control Components – Kollmorgen has launched the VLM servo motor series to fill the gap between stepper and high-performance servo motors. The new VLM series synchronous servo motors offer OEMs, machine builders and end-users, an excellent price-performance proposition in the torque range of 0.5 to 4.5 Nm continuous and 16 Nm peak, with speeds of up to 6000 rpm. They also provide highly flexible configuration, proven quality and high reliability. Hence, they are a very useful solution for many applications where stepper or asynchronous motors are pushed to their limits but the expense and unused dynamics of high performance servo motors is not desirable.

The many standard design and configuration options built into the range allow engineers an optimal solution from the outset, to tailor their applications and machine requirements. Thus, installation time and cost is minimized and the price-performance ratio is further improved. The VLM series motors are available with standard frame sizes of 60 mm and 90-mm or NEMA 23 and 34 in each of the six most popular motor sizes and with a choice of twelve standard windings. The extensive possibilities for shaft and mounting facilitate seamless integration into virtually any system.

Feedback options include Digital Resolver (SFD), resolver, encoder and Hall sensors. VLM motors achieve continuous torque up to 4.5 Nm and peak torque to 16 Nm and can be used in power systems with 230 VAC. And of course, the new motors meet the ROHS Directives for CE and UL certification.

Information on the Kollmorgen VLM Brushless Servo Motors available from Servo2Go.com can be viewed at: https://www.servo2go.com/products/servo-motors-drives/servo-motors/ http://www.servo2go.com/product.php?ID=101027&cat=

These and other Motion Control Products are available through www.Servo2Go.com

For further information on this new product or others in our extensive product portfolio, call 1- 877-378-0240 or e-mail Warren Osak atwarren@servo2go.com or visit Servo2Go.com at: www.Servo2Go.com

For other Motion Control Components, Applications, and Technology from OES (Optimal Engineering Systems) go to: http://MotionControlWeb.com

Servo2Go-Logo
Visit our Website
Twitter Link
Facebook Link

Motion Control – IP65 Integrated Stepper Motors Available from Servo2Go!

Motion Control – Integrated Stepper
motion control - integrated stepper

Greenville, DE —-Motion Control – Applied Motion’s SWM integrated steppers are IP65 rated drive+motor units, fusing step motor and drive components into a single splashproof and dustproof device. This space-saving design eliminates wiring and saves on cost over conventional motor and drive solutions.

motion control - products

The motion control SWM24 integrated steppers combine high torque NEMA 24 step motors with a sophisticated, 6.0 A/phase (peak-of-sine) step motor drive. Power to the drive, located at the rear of the motor, must be supplied by an external DC supply. Applied Motion offers compatible 24 and 48 volt DC power supplies for exactly this purpose.

All SWM24 integrated steppers are RoHS and CE compliant.

Features include:

  • Torque to 340 oz-in
  • Rated IP65 for wet and dusty environments
  • M12 connectors
  • Anti-resonance
  • Torque ripple smoothing
  • Microstep emulation
  • NEMA 24 frame size
  • Stored programming option for stand-alone operation
  • Step direction, velocity and streaming command control modes
  • RS-232, Ethernet and EtherNet/IP Communication options
  • Modbus/RTU for easy communication with PLC or HMI
  • Built-in incremental encoder

CLICK HERE Here for information on these IP65 Integrated Steppers

These and other Motion Control Products are available through www.Servo2Go.com

For further information on this new product or others in our extensive product portfolio, call 1- 877-378-0240 or e-mail Warren Osak at warren@servo2go.comor visit Servo2Go.com at: www.Servo2Go.com


See this and other Motion Control Components from Electromate featured on:

http://MotionShop.com

http://AllMotionBlogger.com

http://Automation-Blogger.com

http://MotionControlBlogger.com

http://motioncontrolBuyersGuide.com

http://MotionControlWeb.com

http://MotionShop.net

http://Catalogs-MotionControl.com

http://MotionControlMarketing.com

http://Gotcha-Stick.com

http://MotionControlMarketing.com

http://Gotcha-Stick.com

Twitter

Facebook

motion control - electromate logo

Motion Control – Closed-Loop Integrated Stepper Motors feature magnetic or absolute encoder feedback Available from Electromate!

Electromate offers JVL Closed Loop Integrated Steppers

Motion Control - Electromate-Logo

 

 

Vaughan, Ontario, Canada — Motion Control Components — JVL presents a new innovative closed-loop stepper motor technology for its NEMA 23 & 34 integrated stepper motor range from 0,1 to 12 Nm. JVL, the European leader in the development of integrated servo and stepper motor technology, has now again developed a new and unique product in the field of integrated motor control.

New Innovative Technology

JVL closed-loop integrated stepper motors, QuickStep®, provide higher torque, faster acceleration, torque control, stall free operation and quieter movements than traditional step motor systems. QuickStep do this with greater efficiency and less motor heating because motor phase current are regulated up and down according to need. Performance of JVL closed-loop steppers are similar to servo motors, but with higher torque and often without need of gearbox, resulting in a more inexpensive solution. Design safety factors have always been high for stepper motors to ensure stall-free operation – now with QuickStep closed-loop control design can be very close to the limit resulting in even lower costs. QuickStep is a true closed-loop control system that compensates step angle errors during a movement and correct errors within a full step. If load becomes too high speed is lowered and position errors will always stay within two full-steps. Smart digital design and very high update rates (36 MHz) means there is no need of any manual adjustment or setup. It works like a perfect stepper motor benefitting from the servo motor technology.

Advantages compared to open loop stepper motors

  • Position feedback and control
  • Fast and easy commissioning. No tuning needed
  • No stalling. No step losses at all
  • Torque control
  • Much faster positioning and more cycles per second
  • Increased efficiency and thereby much lower temperature
  • Shorter settling time
  • Controls higher inertias than open loop steppers
  • Higher load tolerance
  • More quiet operation (lower acoustic noise)
  • Longer lifetime due to lower temperature
  • Correct positioning without overshoot and oscillation

Advantages compared to servo motors

  • Very high Torque at low speed. Often 3-4 times higher in same motor flange size
  • Very high ratio-of-inertia, often up to 40:1
  • Faster commissioning. No tuning needed
  • Lower price. Same price as open loop steppers
  • Totally stiff at standstill. Full holding torque
  • Direct drive without gearbox (better and more precise torque control)
  • Correct positioning without overshoot
  • No oscillation
  • Very short settling time

Benefit in these application from closed-loop stepper motors

  • Multiple axis applications (RS485, CANopen)
  • Industrial Ethernet: Profinet, EtherNet/IP, EtherCAT, Powerlink, Modbus TCP, SERCOS III
  • Magnetic or Absolute Encoder Feedback
  • Positioning tasks with load changes
  • Applications that require quiet operation, short settling times and precision positioning

Applications include

  • Winding applications
  • Belt drives (start/stop, positioning)
  • Dosing pumps and filler systems
  • Semi-conductor mounting
  • Wafer production
  • Textile machines and industrial sewing machines
  • Robotics
  • Testing and inspection systems

More information on the JVL’s Closed-Loop Integrated Stepper Motors can be viewed at the links below-

NEMA 23 models

NEMA 34 models

About Electromate:

Electromate’s Core Purpose is to help Manufacturers build better machines using differentiated automation technology. They specialize in Robotic and Mechatronic Solutions for the Industrial Automation marketplace. Respected by customers as a premiere source for High Performance Automation and Motion Control Components & Systems, Electromate® specializes in AC & DC Servo and Stepper Motors & Drives, Motion & Automation Controllers, Positioning Systems & Actuators, Feedback Devices, Gearing Products and HMI’s & Operator Displays, all supported via extensive product selection, just-in-timedelivery, dedicated customer service and technical engineering support.

More on Electromate can be found at

Website: http://www.electromate.com

LinkedIn: https://www.linkedin.com/company-beta/209277/

Twitter: https://twitter.com/Electromate

Facebook: https://www.facebook.com/electromateindustrial/

Google+: https://plus.google.com/104057418684128701566

Blog: https://electromate.wordpress.com/

Electromate Best Blace to Work

For more information on the “Best Place to Work”CLICK HERE!

To view Electromate’s new corporate video CLICK HERE

To see all of Electromate’s Products and Application Stories featured on MotionShop.com, enter electromate in the Google custom search box (upper left, above)

For further information on this new product or others in our extensive product portfolio, call 1-877-SERVO99 (737-8699) or e-mail Warren Osak at sales@electromate.com or visit Electromate at: www.electromate.com

 

Motion Control – IP65 Integrated Stepper Motors Available from Servo2Go!

Motion Control IP65 Intefrated Stepper available from Servo2Go

motion control Servo2Go-Logo

Greenville, DE —-Motion Control – Applied Motion’s SWM integrated steppers are IP65 rated drive+motor units, fusing step motor and drive components into a single splashproof and dustproof device. This space-saving design eliminates wiring and saves on cost over conventional motor and drive solutions.

The motion control SWM24 integrated steppers combine high torque NEMA 24 step motors with a sophisticated, 6.0 A/phase (peak-of-sine) step motor drive. Power to the drive, located at the rear of the motor, must be supplied by an external DC supply. Applied Motion offers compatible 24 and 48 volt DC power supplies for exactly this purpose.

All SWM24 integrated steppers are RoHS and CE compliant.

Features include:

  • Torque to 340 oz-in
  • Rated IP65 for wet and dusty environments
  • M12 connectors
  • Anti-resonance
  • Torque ripple smoothing
  • Microstep emulation
  • NEMA 24 frame size
  • Stored programming option for stand-alone operation
  • Step direction, velocity and streaming command control modes
  • RS-232, Ethernet and EtherNet/IP Communication options
  • Modbus/RTU for easy communication with PLC or HMI
  • Built-in incremental encoder

These and other Motion Control Products are available through www.Servo2Go.com

For further information on this new product or others in our extensive product portfolio, call 1- 877-378-0240 or e-mail Warren Osak at warren@servo2go.comor visit Servo2Go.com at: www.Servo2Go.com

Servo2Go-Logo
Visit our Website
Twitter Link
Facebook Link

Low-cost Tin-Can Stepper Motors from Nippon Pulse feature high torque and compact size!

Motion Control Low Cost Tin Can Steppers available from Servo2Go

Servo2Go-Logo

Greenville, DE —-Motion Control Components – The PF/PFC series tin-can stepping motors are conventional magnet-driven rotary stepper motors with a permanent magnet in their rotor core. Rotating in proportion to the number of pulses sent to the motor, the stepper motor is frequency synchronized and can change speed depending on the frequency of the pulse signal.

Because of its high torque output and low profile construction, applications for tin-can stepper motors include, but are not limited to, printing, packaging, and medical devices.

PF/PFC series tin-can stepping motors are also available with optional gearheads offering increased torque in a small package. Nippon Pulse geared tin-can stepping motors can achieve up to a 2500mN·m maximum torque.

Geared motors from Nippon Pulse are well-suited for fluid dispensing, pumps, valves and a host of other applications that require high torque and smoother motion.

More information on Low-cost Tin-Can Stepper Motors from Nippon Pulse feature high torque and compact size, available from Servo2Go.com can be viewed at: https://www.servo2go.com/search.php?search=Tin-Can%20Stepper%20Motors&D=PROD

These and other Motion Control Products are available through www.Servo2Go.com

For further information on this new product or others in our extensive product portfolio, call 1- 877-378-0240 or e-mail Warren Osak at warren@servo2go.com or visit Servo2Go.com at: www.Servo2Go.com

Servo2Go-Logo
Visit our Website
Twitter Link
Facebook Link

Integrated IP65 Stepper Motors Available from Servo2Go!

Motion Control Components - Integrated IP65-Stepper Motor available from Servo2Go

Servo2Go-Logo

Greenville, DE —- Motion Control Components – SWM integrated steppers from Applied Motion Products Inc. are IP65 rated drive+motor units, fusing step motor and drive components into a single splash proof and dustproof device. This space-saving design eliminates wiring and saves on cost over conventional motor and drive solutions.

The SWM24 integrated steppers combine high torque NEMA 24 step motors with a sophisticated, 6.0 A/phase (peak-of-sine) step motor drive. Power to the drive, located at the rear of the motor, must be supplied by an external DC supply. Applied Motion offers compatible 24 and 48 volt DC power supplies for exactly this purpose.

All SWM24 integrated steppers are RoHS and CE compliant. Features include:

  • Rated IP65 for wet and dusty environments
  • M12 connectors
  • Anti-resonance
  • Torque ripple smoothing
  • Microstep emulation
  • NEMA 24 frame size
  • Stored programming option for stand-alone operation
  • Step direction, velocity and streaming command control modes
  • RS-232, Ethernet and EtherNet/IP Communication options
  • Modbus/RTU for easy communication with PLC or HMI
  • Built-in incremental encoder

For more information on the SWM Integrated Stepper Motors from Applied Motion Products Inc – CLICK HERE

These and other Motion Control Products are available through www.Servo2Go.com

For further information on this new product or others in our extensive product portfolio, call 1- 877-378-0240 or e-mail Warren Osak atwarren@servo2go.com or visit Servo2Go.com at: www.Servo2Go.com

Servo2Go-Logo
Visit our Website
Twitter Link
Facebook Link

Motion Control – Integrated Stepper Motors with Profinet!

motion control integrated stepper motors

JVL Offers Integrated Stepper Motors with Profinet. The Industrial Ethernet, Profinet, integrates existing systems and equipment bringing the features of Ethernet to the factory floor.

JVL Logo

Birkerød, Denmark and Morrow, OH (USA) –  Motion Control – Recognized as a world leader in integrated motors JVL has added Profinet Industrial Ethernet capabilities to their NEMA 34 Series of integrated steppers with programmable controllers. Available in 4 torque ratings of 3,0 Nm (26.6 in.lb), 6,0 Nm (53.1 in. lb.), 9,0 Nm (79.7 in. lb.), and 12,0 Nm (106.2 in. lb.) these very compact integrated steppers (the MIS340 is just 95 mm (3.74 in. long), include all necessary electronics within the IP67 rated motor housing. the quiet, precision, powerful MIS340 Series steppers are ideal for: Industrial, medical, inspection, testing, and processing applications.

The expanded ethernet protocols of the MIS340 series of integrated steppers from JVL easily connect to Ethernet bus systems such as: EtherCAT, Ethernet I/P, Powelink, ModbusTCP, Sercos III and Profinet. Additionally they are available with bluetooth, ZigBee, WLAN, PLC, RS485, and CANbus. These high performance steppers are also available with separate SMC85 controller. Options include: Electronic gearing, 9.53 mm (0.375 in.) or 14 mm (0.551 in.) diameter shafts, absolute multi-turn encoder, and planetary gear heads.

These high performance steppers feature a very high 409,600 steps per revolution 4,096 microsteps per step) for extremely smooth and quiet operation. The integrated PLC features 8 I/Os, RS-422 and RS485 connections for encoders, and point-to-point or multi axes operations to 254 axes. The 12-80 VDC supply provides high torque (0-9 A RMS (12.6 A peak) at high speed, and the control 12 to 28 VDC can maintain position value, etc. in emergency situations.

About JVL – JVL is recognized as a world leader for its development of efficient and compact integrated motors for VAC and VDC. MAC motor series of integrated VAC servo motors (up to 4500 W and 13,5 kW peak), and the QuickStep integrated stepper motors (up to 25 Nm). Both the servo motor and stepper motor series includes the controller, PLC, encoder, AC power supply and bus system integrated into one compact unit. All industrial ethernet busses like Profinet, EtherCat, Ethernet IP, Modbus TCP, Powerlink, Sercos III etc. are available. Furthermore, traditional modules like CANopen, DeviceNet, Profibus, Nano PLC, RS232/RS485/USB, Process Control can be incorporated.

JVL with more than 25 years of motion control experience enjoys a reputation for the development of highly specialized integrated motors with industrial Ethernet and customized improvements. They work together with their customers and representatives to find an economic, yet technically advanced solution to complicated control applications. JVL’s wide selection of quality products for motion control components include: Integrated VAC and VDC Servo motors, Integrated Stepper motors, VAC Servo motor controllers, Motor drivers (Stepper, VAC and VDC), Brakes, Gears, and HMI Modules.

For further information, please contact: JVL Industri Elektronik A/S, Bregnerodvej 127, DK-3460 Birkerød, Denmark. Tel. +45 4582 4440. E-mail: jvlnyt@jvl.dk. Web: www.jvl.dk

JVL USA • Att: Mike Fisher • National Sales Manager
8610 Morrow-Rossburg Rd • Morrow • OH 45152-9444
E-mail: mfisher@jvlusa.com • Tel.: 513/877-3134 •Tel.: 513/282-0888 (Tech Support Line) •
Fax: 513/877-2471•
For Additional Information about Mike Fisher and JVL USA – Click Here

 

USA and Canada – Reps & Distributors: – Click Here

 

All Other Countries:

Further information can be obtained from:

JVL Industri Elektronik A/S

Bregnerodvej 127, DK 3460, Birkerød, Denmark

E-mail: jvj@jvl.dk Tel.: +45 4582 4440 ; Fax.: +45 4582 5550 ;

For JVL Home Office and World Wide Directory of Reps & Distributors Click Here

JVL Logo
Visit our Website
Order Our Catalog
Request Newsletter
JVL-Trade Fairs
Twitter Link
Facebook Link

Motion Control – Integrated StepSERVO™ Motors Are Available from Electromate!

Automation – Integrated Step Motors fAutomation - Integrated Stepper Motors Available from Electromateuse step motor plus drive and control components into a single device. Integrated steppers offer a space-saving design that reduces wiring and saves on cost over separate motor and drive components.

Motion Control - Electromate-Logo

Woodbridge, Ontario, Canada — Automation motion control – Integrated Stepper Motors – Ideally suited for applications such as packaging and labeling, automated test and measurement, automated assembly and life sciences, StepSERVO™ motors from Applied Motion Products provide the next evolution integrated step motor technology. Starting with a proven integrated motor design, we add a high-resolution incremental encoder and closed-loop servo firmware to create a motor that offers the best step motor performance available today. StepSERVO™ motors offer the same high-torque-at-low-speed and excellent holding torque characteristics of open loop stepping motors with the advantages of true closed-loop control. These advantages include the ability to create peak torques from the motor up to 50% higher than the normal torque range of the same step motor running open loop. Closed-loop also means the motor only draws current when it needs it, so step motors now run cooler than ever before.

StepSERVO™ motors feature:

  • NEMA frame size 17, 23 and 24. StepSERVO motors utilize 5000 line incremental encoders (20,000 counts/rev)
  • NEMA frame size 11. StepSERVO motors utilize 1024 line incremental encoders (4,096 counts/rev)
  • Closed-loop servo control using high torque step motors
  • High acceleration for faster machine cycles and greater productivity
  • Energy efficient, cool running
  • All-in-one compact solution
  • IP65 versions for wet and dusty environments
  • Stand-alone operation (stored Q programming)
  • EtherNet/IP industrial networking option
  • CANopen fieldbus option
  • Modbus RTU option for easy PLC/HMI connection

Click on the following link to view a YouTube Video on the StepSERVO™ integrated stepper motor.StepSERVO™ integrated stepper motors

There are three types of StepSERVO™ to choose from:

SSM integrated steppers feature:

Motion Control SM Integrated Stepper Motors Available from Electromate

  • NEMA 23 frame size motors
  • Ethernet (RJ-45) port for programming
  • EtherNet/IP industrial networking standard
  • Three motor lengths (stack lengths) available to provide the highest amount of torque in the shortest motor possible

TSM integrated steppers feature:

Motion Control TSM Integrated Stepper Motors Available from Electromate

  • NEMA 11 (New!), NEMA 17 and NEMA 23 frame size motors
  • RS-232 or RS-485 port for programming and streaming commandsApplied Motion Products TSM11-1
  • Control options including CANopen fieldbus control, digital step & direction control, analog velocity mode, streaming commands and stand-alone operation using stored Q programs.
  • Three motor lengths available in each frame size to provide the highest amount of torque for each length

TXM integrated steppers feature:

Motion Control TXM Integrated Stepper Motors Available from Electromate

  • IP65 rated for wet and dusty environments
  • NEMA 24 frame size motors
  • RS-232, RS-485 or Ethernet port (M12) for programming, streaming commands and fieldbus/networking
  • Control options include CANopen fieldbus control, EtherNet/IP industrial networking, digital step & direction control, analog velocity mode, streaming commands and stand-alone operation using stored Q programs.
  • Two motor lengths available to provide both a lower torque and a higher torque option depending on application requirements

The family of Integrated Stepper Motors Available from Electromate can be viewed at:http://www.electromate.com/integrated-motors.html

For further information on this new product or others in our extensive product portfolio, call 1-877-SERVO99 FREE (737-8699) or e-mail Warren Osak atsales@electromate.com or visit Electromate at: www.electromate.com

Motion Control - Electromate-Logo
Visit our Website
Motion Control - Electromate Twitter Link
Motion Control - Electromate Facebook Link

Motion Control – Dual Axis Linear Motion Stepper Motors!

H2W Technologies Dual Axis Air Bearing Stepper Stage

H2W Logo

Santa Clarita, CA — Automation Motion Control – Linear Motion — H2W Technologies’ dual axis linear motion stepper motors are ideal for open loop positioning applications requiring 2 axis of motion in a single plane. They can perform at speeds of up to 80 in/sec [2 m/sec] and strokes of up to 20 in x 30 in [0.5 m x 0.75 m]. Linear stepper motors are capable of very precise position, velocity, and acceleration control when coupled with a micro-stepping drive and indexer.

The moving assembly called the “forcer” is supported by magnetically preloaded air bearings that are imbedded in the active surface of the forcer. The bearings are designed to support the customer’s payload and to maintain the required 0.0005 in to 0.0010 in [12 to 25 micron] gap between the platen and the forcer.

The step and direction signal for each linear motion axis comes from two separate micro-stepping drives (2 or 4 phase). A 2 axis indexer is required to send step and direction signals to the drivers. For 2 phase motors, the full step is 0.010 in [250 microns] and for 4 phase motors the full step is 0.005 in [125 microns]. With micro-stepping, resolutions in the order of 0.5 to 1 micron are achievable.

The dual axis linear stepper motor is a complete 2 axis, single plane air bearing positioning system with the motor, the bearings, and the positioning system all built into one compact package. Integrating linear encoders with the stepper motor allows for a hybrid, closed loop positioning system.

Advantages:

  • Low profile and small cross section
  • High Speed
  • No servo tuning required
  • Multiple forcers on a single platen

Applications:

  • Pick and Place
  • Wire bonders
  • Parts transfer
  • Fiber optic

H2W Technologies, Inc. is dedicated to the design and manufacture of linear and rotary motion products that are used in the motion control industry. The complete line of linear electric motors includes: Single and dual axis linear steppers, DC brush and brushless linear motors, voice coil actuators, and AC induction motors. Also offered is a complete line of ball screw, lead screw and belt driven positioning stages.

Other motion control products include: Limited angle torque motors for compact, limited angular excursion rotary servo applications, 3 phase brushless rotary servo motors with matching digital servo amplifiers and permanent magnet linear brakes for fail-safe, zero power braking for baggage handling and people moving applications as well as amusement park rides.

With over 75 years combined experience in the linear and rotary motion field, the H2W Technologies team of engineers offers the optimal solution to the most demanding motion control, requirements.

For additional information contact Mark Wilson at H2W Technologies, 26380 Ferry Ct, Santa Clarita, CA 91350; Tel: 888-702-0540, Fax: 661-251-2067, E-Mail:info@h2wtech.com or visit the website at http://www.h2wtech.com

H2W Logo
Visit our Website
You Tube

Integrated QuickStep NEMA23 Stepper Motors, A Wise Choice When Building an Automation/Motion Control System!

Motion Control MIS 23 Stepper Motors from JVL

JVL Logo

Birkerød, Danmark, and Morrow, OH — MIS23 QuickStep stepper motors are a series of versatile, compact, economical integrated stepper motors from JVL. Integrated stepper motors in the MIS23 series have NEMA 23 flange dimensions of 57×57 mm and are available in three models with rated torques of: 1.1 Nm (MIS231), 1.6 Nm (MIS232), 2.5 Nm (MIS234) (1000 RPM @ 48VDC). To reduce cost and protect against electrical noise many of the control and communication functions have been integrated with the motor in a housing designed to provide IP42, IP55 or IP65 protection, and eliminating the need for running control and communication cables. Different PCB’s (modules) can be mounted within the housing to create an automation/motion control system that is easy to incorporate into new and existing applications.

Among the many features that can be integrated are: Pulse/direction driver, serial RS485 position controller with easy graphical programming, point-to-point or multiaxis operation up to 255 axes on the same RS485 bus, CANOpen DS-301 and DSP-402, optional absolute singleturn magnetic encoder with resolution of up to 1024 pulses/revolution for stall detection, 8 I/O that can be configured as input, output or 10bit analogue input, electronic gearing for following an encoder or pulse train in an arbitrarily selectable controlled ratio, high speed position capture.

The MIS23 Series of stepper motors follows the same protocol as MAC motors so that MAC motors and QuickStep motors can be connected to the same RS485 bus, and a double voltage-supply available so that position and parameters are maintained during emergency stop. They also feature: Fixed 1600 pulses/revolution for version with built-in position controller, 200, 400, 800, 1000, or 1600 pulses/revolution for versions with pulse/direction inputs.

All modules are supplied with M12 connectors. MIS23 QuickStep motors require a power supply of 12-48V DC. Backlash-free and planetary gears in different ratios can also be supplied. Additionally the Quickstep series also includes larger versions like the MIS34 (NEMA 34), MIS43 (NEMA 43), and MIS51 (NEMA 51) with even more options, such as Ethernet.

About JVL – JVL is recognized as a world leader for its development of efficient and compact integrated motors for VAC and VDC. MAC motor series of integrated VAC servo motors (up to 4500W and 13,5kW peak), and the QuickStep integrated stepper motors (up to 25Nm). Both the servomotor and stepper motor series includes the controller, PLC, encoder, power supply and bussystem integrated into one compact unit. All industrial Ethernet protocols like Profinet, EtherCAT, Ethernet/IP, Modbus TCP, Powerlink, Sercos III etc. are available. Furthermore, traditional modules like CANopen, DeviceNet, Profibus, Nano PLC, RS232/RS485/USB, Process Control can be incorporated.

JVL has more than 25 years of motion control experience and enjoys a reputation for the development of highly specialized integrated motors with industrial Ethernet and customized improvements. They work together with their customers and representatives to find an economic, yet technically advanced solution to complicated control applications.

JVL’s wide selection of quality products for motion control components include: Integrated VAC and VDC Servo motors, Integrated Stepper motors, VAC Servo motor controllers, Motor drivers (Stepper, VAC and VDC), Brakes, Gears, and HMI Modules.

For further information, please contact: JVL Industri Elektronik A/S, Bregnerodvej 127, DK-3460 Birkerød, Denmark. Tel. +45 4582 4440. E-mail: jvlnyt@jvl.dk. Web: www.jvl.dk

JVL USA • Att: Mike Fisher • National Sales Manager
8610 Morrow-Rossburg Rd • Morrow • OH 45152-9444
E-mail: mfisher@jvlusa.com • Tel.: 513/877-3134 •Tel.: 513/282-0888 (Tech Support Line) •
Fax: 513/877-2471•
For Additional Information about Mike Fisher and JVL USA – Click Here

 

USA and Canada – Reps & Distributors: – Click Here

 

All Other Countries:

Further information can be obtained from:

JVL Industri Elektronik A/S

Bregnerodvej 127, DK 3460, Birkerød, Denmark

E-mail: jvj@jvl.dk Tel.: +45 4582 4440 ; Fax.: +45 4582 5550 ;

For JVL Home Office and World Wide Directory of Reps & Distributors Click Here

JVL Logo
Visit our Website
Order Our Catalog
Request Newsletter
JVL-Trade Fairs
Twitter Link
Facebook Link