Category Archives: Gearmotor – Miniature

Motion Control – Maxon introduces a multi-axis controller for highly dynamic positioning tasks!

Motion Control – Miniature Multi-axis Controller

Maxon is launching the next generation of Motion Controllers with its MiniMACS6-AMP-4/50/10. The controller is ideal for use in applications where PLC solutions may be too expensive or cannot meet customer-specific requirements.

motion control - miniature controller

Taunton, MA — Motion Control Products – Maxon’s new multi-axis controller, the MiniMACS6-AMP-4/50/10, offers precise and highly dynamic control of up to six brushed DC motors or four brushless DC motors (up to 540 W continuous output power and 1.6 kW peak output power).

motion control - maxon motors

 

 

The controller is an economical and compact solution for system designers who develop autonomous robots or shuttle systems

A significant advantage of the new multi-axis solution is that it is programmable with the comprehensive ApossIDE automation software and the license-free Motion Control Library (written in C). Integrated bus interfaces enable efficient data exchange with higher-level controllers; however, it is also possible to run complete process sequences autonomously, without a PLC or PC. The MiniMACS6-AMP-4/50/10 will be available in early 2021.

Motion Control – Maxon drives are on the Red Planet with NASA’s Perseverance Rover!

Motion Control – Application – Maxon drives on the Red Planet!

In July, NASA sent its fifth rover to Mars. Its main mission is to collect soil samples that will be analyzed on Earth at a later time. The rover also carried a helicopter that is performing flights on the Red Planet. maxon’s precision DC and BLDC motors are used for numerous mission-critical tasks.

motion control - maxon motors

 


motion control - maxon motorTaunton, MA — Motion Control Products & Application – maxon drive systems are very familiar with Mars. Our drives have been used in virtually every successful robotic mission over the last three decades. There are now more than 100 of them on the Red Planet and there are likely to be more soon. The launch window for NASA’s next mission opens on July 22nd. An Atlas V rocket will launch the new Perseverance rover on its way to Mars, where it will be searching for signs of previous life on the planet. Its most important job is to take multiple soil samples, seal them in containers and deposit them on the surface of Mars so that a future mission can return them to Earth. Several maxon motors will be used to handle the samples inside the rover. For example, maxon DC motors are installed in the robotic arm, which moves the samples from station to station. Maxon motors will also be used for sealing and depositing the sample containers.

NASA’s Jet Propulsion Laboratory (JPL), is carrying out the mission, and have asked maxon to produce 10 drives for the rover. As with almost all previous Mars missions, these drives are based on standard products from maxon’s catalog with modifications. For the first time, NASA is using brushless DC motors, including: nine EC 32 flat and one EC 20 flat in combination with a GP 22 UP planetary gearhead. Working closely with JPL specialists, maxon engineers developed the drives over several years and tested them thoroughly to achieve the highest standards of quality. “We’ve learned a lot from this exciting project,” says Robin Phillips, head of the maxon SpaceLab. “We now have very broad expertise in space applications and have established quality assurance processes that meet the expectations of the industry. Customers from other industries such as the medical sector, where requirements are often similar, can also benefit from this know-how.”  Space missions place the highest demands on drive systems. This includes vibrations during the rocket launch, vacuum during the journey, impacts on landing, and the harsh conditions on the surface of Mars, where temperatures fluctuate between -125 and +20 degrees Celsius and dust penetrates everywhere

Maxon DC motors control the Mars helicopter.

motion control - maxon mars motor

The Perseverance rover is expected to land on Mars on February 18, 2021 – but it won’t be alone. A drone helicopter called Ingenuity will be attached to the underside of the rover. It weighs 1.8 kilograms, is solar powered and will perform several short flights, as well as take aerial images. The main goal of this experiment is to test the concept for further drones of this kind. maxon has six brushed DCX motors with a diameter of 10 millimeters controlling the tilt of the rotor blades and the direction of flight. The drives are very light, dynamic and highly energy-efficient. These properties are crucial, because every gram counts on the Mars helicopter. Flying on Mars is not easy. The atmosphere is extremely thin, roughly comparable to the conditions on Earth at an altitude of 30 kilometers. The drone helicopter has flown in a simulated test environment in the JPL laboratory. Whether it will lift off on Mars remains to be seen. First, other obstacles, such as the rocket launch, must be successful. “We hope that everything goes well and that we’ll soon see our drives in action on Mars,” says maxon CEO Eugen Elmiger. “We’re all keeping our fingers crossed.”

motion control -maxon miniature motors

For additional information, please contact us at info.us@maxongroup.com or 508-677-0520.

About Maxon

maxon is a developer and manufacturer of brushed and brushless DC motors, as well as gearheads, encoders, controllers, and entire mechatronic systems. With over 50 years of experience in drive technology, maxon works closely with engineers designing high-tech innovations. maxon drives are used wherever the requirements are particularly high: in NASA’s Mars rovers, in surgical power tools, in humanoid robots, and in precision industrial applications. Worldwide, maxon has more than 2800 employees at nine production sites and is represented by sales companies in more than 30 countries. www.maxongroup.com/maxon/view/content/index

Contact maxon for more details https://support.maxongroup.com/hc/en-us/requests/new

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

motion control - handbook


See this and other Motion Control Components from Maxon featured on:

http://MotionShop.com.com

http://AllMotionBlogger.com

http://Automation-Blogger.com

http://MotionControlBlogger.com

http://MotionControlBuyersGuide.com

http://MotionControlWeb.com

http://MotionShop.net

http://Catalogs-MotionControl.com

Request 2020/2021 Maxon Catalog

motion control - maxon logo

Motion Control – Electromate Recognized with 2021 AHTD Foundation Award!

Motion Control – Electromate 2021 AHTD Foundation Award!

motion control - electromate components


motion control - electromateToronto, Ontario – June 18, 2021 – Electromate received a Foundation Award from the Association for High Technology Distribution (AHTD), recognizing the company’s 25 years of membership and support. This is the first year the Award has been given, honoring a small group of members out of approximately 300 automation solution providers and manufacturers.

The AHTD is dedicated to maximizing the productivity, growth, and enterprise opportunities of its high-tech automation solution provider and manufacturer members. These goals align with Electromate’s commitment to driving innovation, identifying emerging technologies and products, promoting the education of automation and motion control, and fostering its relationships with industry peers.

Motion Control – maxon celebrates International Women in Engineering Day!

Motion Control – maxon celebrates International Women in Engineering Day!

The women in engineering (WIE) at maxon work eagerly to contribute to the success of advanced technology in the motion control industry. This week in honor of International Women in Engineering Day, June 23, 2021 – maxon wishes to thank these engineering women for their contributions as they continue to help shape the world we live in.

motion control - engineers


motion control - maxon motorsTaunton, MA — Around the globe, the maxon women in engineering are working on motion control applications with their customers, they focus on new product designs to implement the latest technologies and continue to research new concepts and ideas for drive systems to be used in motion control applications found in Medical, Industrial Automation, Aerospace and Defense, and Mobility industries.

Motion Control Application – Congratulations to Emirates Team New Zealand – Winner of the 36th America’s Cup!

Motion Control Application – Motors

They have gone and done it again. Emirates Team New Zealand have retained the America’s Cup over the Italian Challenger Luna Rossa Prada Pirelli.

motion contyrol - motor application


motion control - maxonTaunton, MA — Motion Control Products – maxon Group extend their heartfelt congratulations to Emirates Team New Zealand. In the historical 36th America’s Cup that endured extra challenges including Covid-19, race cancellations and delays meaning interruptions and last-minute tactical changes, the Kiwis have retained the oldest trophy in international sporting history.

Motion Control – Maxon Gearheads – Great power in Compact Form!

Motion Control – Maxon Gearheads – Great power in Compact Form!

motion control - gearhead cutaway

Micro gearheads from maxon with improved efficiency.

Taunton, MA — Motion Control Products – Maxon has developed a unique upgrade in the form of a new product series for its standard micro gearhead: A wide range of performance improvements offer new opportunities.
motion control - maxon

 

The first ideas for the UP-gearhead were inspired by ESA’s Mars project ‘ExoMars’ and NASA’s ‘Mars 2020’ project, where there was a need to ensure the highest possible availability even in extreme environmental conditions.

This also directly affects further parameters of the drive system: Given the same input power, ie. using the same motor and the same motor control system, the gearhead can deliver 30% more torque.

Motion Control – The Mars helicopter makes history – with maxon’s precision motors!

Motion Control – Mars helicopter has maxon’s motors!

Space fans are thrilled: NASA’s Ingenuity helicopter has successfully completed its pioneering flight on Mars. This is the first time in the history of powered, unmanned spaceflight that a device has flown in a controlled manner on another planet.

motion control - mars helicopter


motion control - maxonTaunton, MA — Motion Control Products – A short flight for “Ingenuity,” but a big success for unmanned space flight. NASA’s Mars helicopter flew over the surface of the Red Planet for about 40 seconds on Monday, April 19th and landed back on four legs. From NASA’s perspective, this is a historic event similar to the Wright brothers’ first controlled flight in 1903.

With the Mars helicopter, the concept of powered, unmanned, and autonomous flights on foreign planets is being tested. This is comparable to the first Mars rover “Sojourner”, which paved the way for scientific follow-up missions such as “Curiosity” and currently “Perseverance”. “Ingenuity” is about to complete several flights over a period of 30 days, each lasting up to 90 seconds and reaching a maximum altitude of five meters.

Motion Control – Maxon precision motors Go to Mars AGAIN!

Motion Control – Maxon motors on Mars!

motion control - miniature motors

 

motion control - maxon logo

 

 

Taunton, MA — Motion Control Products – NASA’s Perseverance rover landed on Mars on February 18th. Was there once life on Mars? This is the question that one of the most complex robotic systems ever built by humankind has set out to answer. Several of maxon’s electric drives are used for handling the soil samples—and to control the first Mars helicopter.

Will NASA, the US space agency, successfully land a fifth rover on Mars, allowing it to start its series of missions to bring Mars soil samples back to Earth? The rover named Perseverance will enter the atmosphere of the Red Planet on February 18th—after traveling a distance of more than 470 million kilometers.

Motion Control – 5 challenges an electric motor has to overcome on Mars

Motion Control – Electric motors on Mars

Outer space is unforgiving. This is why precision drives embarking on a trip to other planets need to meet extremely high-quality standards.

motion control - motor for mars

motion control - maxon

 

Taunton, MA — Motion Control Products – Every Mars drive from maxon is based on a catalog product and is modified for the specific mission. That’s because the DC motors, gearheads, and encoders face brutal conditions during liftoff, the long journey through space, and the mission on the Red Planet. In this blog, I will talk about the properties a drive needs to have to qualify for a journey to Mars.

Motion Control – Maxon’s trade show experience goes virtual!

Motion Control – Virtual Trade Show!

motion control - trade show

 

motion control - maxon logo

 

 

Taunton, MA — Motion Control Products – This year, the COVID-19 pandemic has led to the cancellation of nearly all trade shows. Despite this, maxon is offering a digital trade show experience to all of its customers and anyone who’s interested in learning about the latest in drive technology. Visitors to maxon’s virtual booth will discover the benefits of our latest products such as the MiniMACS6 master controller, learn about high torque brushless DC motors as well as flat motors for robotics, and get to know the Mars rover. Visit virtualbooth.maxongroup.com and contact us to get your ideas moving.

Drive specialist maxon, renowned for its Mars motors, is joining forces with the robotics startup ANYbotics!

Motion Control – Maxon and ANYbotics form New Partnership!

Motion Control Drive specialist maxon, renowned for its Mars motors, is joining forces with the robotics startup ANYbotics and will in future supply the drive systems of the autonomous ANYmal inspection robot. The robot will soon be marketed in large quantities. This cooperation will also benefit maxon, since ANYbotics provides important robotics know-how and is currently the most successful young company in this field.

motion control - maxon to supply drive systems

motion control - maxon logoThe maxon Group contributes 60 years of experience in drive technology to the partnership, as well as a global production infrastructure and validated processes, and will help to advance the industrialization and commercialization of ANYmal – with competitive, high-performance drive systems, twelve of which are used in each robot. “In maxon, we have found the ideal partner for taking care of our drive technology as we transition from small series to mass production. With maxon’s expertise and infrastructure, we will be able to further optimize a core element of our robots and access state-of-the-art production methods,” says Péter Fankhauser, CEO of ANYbotics.Taunton, MA — Motion Control -A solid partnership: maxon and ANYbotics are entering into a close, long-term collaboration and are thus strengthening Switzerland as a prime location for robotics. One of the decisions made by the two partners is that maxon, as global drive specialist, will handle the future development and production of the actuators for ANYmal. ANYmal is an autonomous, four-legged robot that is capable of inspecting and monitoring industrial systems and is destined to also take on dangerous maintenance tasks in the future. The robot can even cope with difficult infrastructures such as stairs and inclines, and is used in a wide variety of industries.

ANYbotics recently won the Swiss Economic Award 2020 and has been chosen as the best young entrepreneur in Switzerland in the Hightech/Biotech category. The company has valuable experience in robotics – a market that offers great potential for maxon. Eugen Elmiger, CEO maxon Group, says: “By collaborating with ANYbotics, we are merging know-how from different worlds. The creativity and high responsiveness of a startup are paired with the global and stable industrial environment of the maxon Group. Together we will create an energy-efficient and intelligent robotic drive, the likes of which has never been seen before.” To further cement the partnership, the two companies are also getting closer geographically: maxon, which has its headquarters in the canton of Obwalden, is opening a lab at the Züri.ch Campus in the Oerlikon district of Zurich, in close proximity to ANYbotics. Here the engineers and technicians will meet to discuss the progress on their projects. Additionally, maxon wants to use the lab to get even closer to ETH Zurich and the University of Zurich, offer technical support to young engineers, provide workspaces, and get talent on board. Eugen Elmiger says: “We are already heavily involved with vocational education in and around Zurich and Lucerne. With the new lab, we will be in an even better position to support talents in drive technology and robotics.”

The Swiss specialist for quality drives

Maxon is a developer and manufacturer of brushed and brushless DC motors, as well as gearheads, encoders, controllers, and entire mechatronic systems. maxon drives are used wherever the requirements are particularly high: in NASA’s Mars rovers, in surgical power tools, in humanoid robots, and in precision industrial applications, for example. To maintain its leadership in this demanding market, the company invests a considerable share of its annual revenue in research and development. Worldwide, maxon has more than 3000 employees at nine production sites and is represented by sales companies in more than 30 countries.

 

ANYbotics: Mobile robots for industrial applications

ANYbotics AG is a young company that develops autonomous robots that independently inspect and monitor industrial systems. ANYbotics was born in 2016 as spin-off from ETH Zurich. It was founded with the purpose of commercializing the technology behind the four-legged ANYmal robot. Today, ANYbotics is one of the world’s leading developers of mobile robotics for complex industrial environments. A staff of 50 develops and markets the technology for use in the energy, process and construction sectors.

About Maxon

maxon is a developer and manufacturer of brushed and brushless DC motors, as well as gearheads, encoders, controllers, and entire mechatronic systems. With over 50 years of experience in drive technology, maxon works closely with engineers designing high-tech innovations. maxon drives are used wherever the requirements are particularly high: in NASA’s Mars rovers, in surgical power tools, in humanoid robots, and in precision industrial applications. Worldwide, maxon has more than 2800 employees at nine production sites and is represented by sales companies in more than 30 countries. www.maxongroup.com

Contact maxon for more details https://support.maxongroup.com/hc/en-us/requests/new

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

motion control - handbook


See this and other Motion Control Components from Maxon featured on:

http://MotionShop.com.com

http://AllMotionBlogger.com

http://Automation-Blogger.com

http://MotionControlBlogger.com

http://MotionControlBuyersGuide.com

http://MotionControlWeb.com

http://MotionShop.net

http://Catalogs-MotionControl.com

Request 2020/2021 Maxon Catalog

motion control - maxon logo

Motion Control Application – Twenty-twenty Vision – Maxon Components Allow Surgeon to Not only See But to Feel!

Motion Control Application –

While robotic assistance systems are available for most types of surgery today, eye surgery used to be an exception. A Dutch company has changed that. A world first in eye surgery.

 

Maxon Logo

motion control component used in eye surgery

© 2016 Preceyes

Fall River, MA — Motion Control Components Application – Worldwide, about 50 to 70 million people are suffering from visual impairment due to disorders of the retina. Adequate treatment is still impossible in many cases. Eye operations are always a big challenge for a surgeon, and steady hands are a key requirement. Surgeries like those for treating a detached retina require extreme precision. And when it comes to precision, human hands can’t hold a candle to robotic systems.

Ten to twenty times better precision

This is why the company Preceyes, which originated as a spin-out from the University of Eindhoven (Netherlands), has developed a completely new robotic system for eye surgery. Specially designed for the treatment of retina disorders, the assistance system improves precision by a factor of 10 to 20 compared with the human hand. This allows operations to be performed that are currently impossible due to lack of precision – an enormous gain for patients, but also for surgeons, whose effectiveness and accuracy will be vastly improved

motion control haptic robotic component

The new robotic system is used in surgery to treat disorders of the retina. Image © Preceyes

The world’s first robot-assisted operation inside the eye was performed successfully at the John Radcliffe Hospital, Oxford. “This is the culmination of 10 years of work. The ease with which Professor MacLaren was able to perform the surgery is an important step ahead for robot-assisted eye operations and a clear vindication of our technology,” says Marc de Smet, MD Chief Medical Officer at Preceyes.

Haptic feedback

The functional principle is straightforward: While the operating surgeon is sitting next to the patient’s head looking through a microscope, he is operating a joystick whose motion is transmitted to a robotic arm (slave). The robot downscales the motion: When the surgeon moves the joystick by a centimeter, the tip of the robotic arm moves only by a millimeter. Meanwhile, the other hand performs manual tasks as required. The system is designed to allow surgeries to be performed with motion control alone as well, using two joysticks and two robotic arms..

In addition to a haptic feedback function that not only lets the surgeon see but also feel his actions, the robotic system also supports quick retooling. This is an important factor because it reduces the time required for an operation. The motions of the robotic arms are performed by high-precision drive systems of maxon.

Contact maxon for more details info@maxonmotorusa.com

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

Maxon Handbook Banner


For other Motion Control Components, Applications, and Technology from Maxon Motor go to: http://AllmotionBlogger.com
 

Maxon Logo
Visit our Website
Order Our Catalog

Motion Control Application – Please smile with maxon motors!

Motion Control Application – Digital SLR cameras can deliver extremely sharp photos – regardless of whether the photographer is a professional or a hobbyist. Not only does the skill of the photographer, but also the technology inside the camera play a key role. maxon drive systems help to create lightning-fast images.

motion control - leica lens with motor

 

Maxon Logo

Fall River, MA — Motion Control Components Application – A maxon A-max 12 with precious metal brushes is installed in the central shutter of the S lens. The maxon A max program stands for high-quality DC motors with an optimal price/performance ratio.

With its Leica S system, camera manufacturer Leica offers a unique combination of performance features for digital photography. It combines the image quality of a medium-format camera with the handling, speed and flexibility of a small-format camera. The lenses used in the Leica S system have a built-in dedicated processor for controlling the auto focus. The lenses are also available with a central shutter for maximum flexibility when using a flash. Besides the focal-plane shutter, which is integrated in the camera, the central shutter is one of two common designs. The central shutter is typically located at a “central” position in the lens assembly, between the optical lens elements. It consists of several blades arranged around the optical axis in a concentric pattern. When the shutter release of the camera is pressed, the blades snap back from this axis synchronously and let the light fall on the sensor.

With SLR cameras, the central shutter first closes after the shutter release, because all the settings were made with an open shutter. The mirror swings up, then the central shutter opens for the duration of the exposure before closing again. Finally, the mirror swings back into the path of light, and the shutter opens. Even though it employs the classic solution of mechanical springs for the efficient storage of potential energy, the central shutter is a piece of cutting-edge technology. The tensioned-spring principle contributes significantly to the extremely compact dimensions.

Small motor for high tension

The springs are tensioned by a specially developed maxon motor with a high-precision overrunning clutch and release their stored energy to activate the shutter blades when the shutter release is depressed. A specially constructed solution prevents the blades from rebounding when the shutter is opened or closed. A microprocessor-controlled pawl and ratchet mechanism controls the shutter cycle via two electromagnetically activated plungers.

The gear motor of maxon motor is used for tensioning three springs that store the energy for the central shutter. A maxon A-max 12 motor is used as the base motor. The gearhead is an all-new development and is adapted to the available space. This presented a special challenge to the gear motor in the central shutter of the Leica lens. What was needed and developed was a very compact, enclosed and sealed custom version of the gearhead with perpendicular power transmission to toothed gear of the central shutter through a crown gear, for a life span of more than 100.000 releases.

Contact maxon for more details info@maxonmotorusa.com

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

Maxon Logo
Visit our Website
Order Our Catalog

Motion Control – More versions, more power – The New DCX Motors and GPX Gearboxes!

New additions to the maxon family of X drives

Maxon motion control DCX Motors and GPX Gearboxes Overview

Maxon Logo
Visit our Website
Order Our Catalog

Fall River, MA – Motion Control – Now even stronger, more efficient and with yet more combination options: There are new additions to the maxon family of X drive products. Several long versions of brushed DC motors, with higher torques and more power, are being added to the product range, together with matching planetary gearheads. Each of the 3-stage versions can now be combined with the next smaller motor. This saves space, weight and costs.

Two years ago, maxon motor introduced a new generation of brushed DC motors – the maxon X drives. These are extremely powerful, easy to configure online, and ready for shipment within 11 days. Now, four more motor sizes are being added to the existing portfolio. The 14, 16, 22 and 26 mm diameter models are now each available in a long version (L), which offers higher continuous torque and higher continuous output power.

At the same time, maxon motor is introducing four new GPX planetary gearheads, in the sizes 14, 19, 26 and 37 mm, compatible to existing products in the program. These gearheads are designed with scaled gear stages. Each of the new 3-stage gearheads can be driven with the next smaller motor. This brings many advantages, as the resulting drive system is smaller, lighter and more economical.

That’s not all, starting immediately, the existing GPX 16 and GPX 32 models are available in various versions and can be equipped with ceramic axles to reduce wear. Customers looking for a particularly low-noise gearhead have the option of choosing plastic planetary gears.

Maxon also expanded the encoder portfolio. The new ENX 16 Easy absolute encoder is available as an SSI or BiSS-C version, according to the customer’s requirements.

All new products are available in the online shop starting immediately. They can be easily configured together with the other maxon X drive products: Customers select the desired motor, the matching winding, brushes and shaft length, as well as the gearhead and encoder. The configured product is ready for shipment in 11 days or less. For more information, go to dcx.maxonmotor.com.

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website atwww.maxonmotor.com.

 

Motion Control – MAXON Says, “Customize Your Drive System Online!”

Maxon motion control X-Drives Configure online

 
 
 
 
 
 
 
 
 

Maxon motors introduces a NEW product line of innovative brushed DC motors, planetary gearheads and encoders. customers will find the new motors available for easy online configuration in the online shop. Within 11 working days, the finished drives are ready for shipment. Profit from these fast delivery times now!.

Maxon Logo

Fall River, MA — Maxon motor is introducing new high-speed drives for you to configure. The brushless ECX motors with diameters of 8, 16 and 19 mm achieve peak values of 120,000 rpm, run very smoothly and develop hardly any heat. They are available with different power stages and in standard or sterilizable versions (up to 2000 autoclave cycles). That makes the drives an attractive option for hand-held surgical tools as well as industrial spindles.

Configurable drives: dynamic, high power, and low noise

Configure and combine the DC motor (DCX, DC-max) or BLDC motor (ECX SPEED) and planetary gearhead (GPX) and sensor (ENX) according to your individual requirements, easily and online. After only 11 working days, the drive systems are ready for shipment from Switzerland. Detailed product data can be viewed online immediately and 3D data for the configuration is available for download. Discover the world of maxon X drives!

maxon X drives program

Maxon motion control X-Drives Configure online

High power density, high efficiency, smooth running and available for online configuration.Configure sizes from Ø 10 – 35 mm. Choose between precious metal or graphite brushes, ball or sintered bearings, and much more.

 
 
 
 
 

Maxon motion control X-Drives Configure online

The DC motors with the best price/performance ratio can be configured online. Configure Ø 16 and 22 mm sizes. Choose between graphite and precious metal brushes, sintered and ball bearings, and many other components.

 
 
 
 
 
 

Maxon motion control X-Drives Configure online

Super-fast, configurable brushless DC motors. The brushless ECX series of motors has been optimized for high speeds (up to 120,000 rpm) and withstands up to 2000 autoclave cycles

 
 
 
 
 
 
 

Maxon motion control X-Drives Configure online

Configurable planetary gearheads for high torques in the smallest of spaces. Maxon GPX gearheads are low-noise and low-backlash. Ideal for when high torques and speeds are needed.

 
 
 
 
 
 

Maxon motion control X-Drives Configure online

Configurable digital encoders. 3-channel encoders with inverse signals for interference free function. The counts per turn may be easily programmed at production.

 
 
 
 
 
 
 
 

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

Motion Control – Maxon Sets New Standards in Micro Drives!

–High Performance Drive in a Small Package!

Maxon’s smallest DC brushless motor is only four millimeters in diameter and comes in two different lengths. Certified in accordance with ISO 13485, the new brushless micro drive is ideal for medical applications.

Maxon motion control EC4 motor for medical applications

Maxon Logo

 

Fall River, MA — Motion Control — The EC 4 brushless DC motor is maxon motor’s ultra-compact solution to the market needs. As the smallest micromotor to come from the Swiss manufacturer, the EC 4 is only four millimeters in diameter. It is available in two lengths, with power ratings of 0.5 and 1 W. Equipped with an ironless maxon winding, the EC 4 stands out for its robust design, high power density, and energy efficiency.

Maxon has the matching gearhead

Maxon motion control EC4 micro motor

Combined with the GP 4 planetary gearhead, the EC 4 becomes a compact drive for use in micropumps, analytic and diagnostic devices, and laboratory robots. Precise and reliable, it can adjust lenses, dispense fluids, or position sensing devices. All units meet the ISO 13485 medical standard, which makes this maxon micro drive the perfect choice for applications in medical technology.

Maxon offers a complete line of dc motors, gearheads and controllers. Contact us to help find the right solution for your application. info@maxonmotor.com

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

Motion Control – EC-4 Pole 32 HD with Planetary Gearhead!

The new maxon EC-4pole 32 HD motor has been designed for extremely rough operating conditions, particularly applications in deep drilling. This 480 W motor can withstand 200 °C, 1000 G, -5000 m and 1700 bar.

Maxon motion control EC32 Hight Temp Motors are Ideal for Deep Hole Drilling

Maxon Logo

Fall River, MA — Deep drilling technology (called “downhole drilling” in the field of oil and gas exploration) makes it possible to recover oil and gas from depths of more than 2500 m. By combining deep drilling with directional drilling (dynamic position alignment of a bore in the earth), previously unreachable oil reserves are being opened up, with drilling depths of approx. 5000 m and drill lengths of up to 11000 m. The development of specialized electronics and drives has made it possible to better monitor and control many functions across the entire drilling process. For instance, it is now possible to dynamically measure and adjust the position of the drill head during the drilling process. Diverse deep drilling tools also use hydraulic valves or flaps that are operated by electromechanical drives. The temperatures and pressures at these depths, combined with the strong vibrations that occur during the drilling work, present unique challenges for the use of electronic drives.

The different versions of the EC-4pole 32 HD are designed for operation in air or in oil (flooded in hydraulic oil). The power rating depends on the surrounding medium and amounts to 220 W in air and, due to the much higher heat flow, 480 W in oil. They are designed for ambient temperatures of more than 200 °C and atmospheric pressures of up to 1700 bar. The Ø 32 mm motors must also be able to withstand vibrations of up to 25 grms as well as impacts of up to 1000 G (1000 times the acceleration due to gravity at the earth’s surface). As an example, a Formula 1 vehicle is exposed to approximately 2 G and fighter jets are exposed to approximately 13 G. The motors feature high efficiency (up to 89% in air, more than 80% in oil), making them ideal for use in battery-operated applications. With their detent-free running properties, they have excellent control characteristics and are suitable for high-precision positioning tasks in outer space, even at low speeds.

Maxon motion control EC32 Hight Temp Motors are Ideal for Deep Hole Drilling

The EC-4pole 32 HD is ideal for use in environments with extreme temperatures, subject to high vibration, or under ultra-high vacuum. This means the motors can also be used in aerospace applications, e.g. for gas turbine starters, for the generators of jet engines, for regulating combustion engines, or for exploration robots. For the use of the motor in conjunction with a gearhead, maxon offers the GP 32 HD, a powerful and robust planetary gearhead.

 

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

Motion Control – DCX Configurable DC Motors and Gearheads!

Maxon Motor’s DCX series is being expanded with two new DC motors. The GPX 22 gearhead is now also available in a version with reduced noise level and with ceramic axes.

Maxon Motion Control Configurable DCX Motors and Gearheads

Maxon Logo
Visit our Website
Order Our Catalog

Fall River, MA — In addition to the maxon DCX 10L, a shorter version is now also available, the DCX 10S. Like all motors in the DCX series, this brushed DC motor excels through high power density and low vibration. The DCX 10S exceeds the 1 mNm threshold during continuous use. With its mechanical output power of up to 1.4 W in a 10 mm diameter, it is a real powerhouse. Regardless of whether this electric motor is equipped with sintered bearings or ball bearings, the DCX 10S works at a whisper of approximately 35 dBA*.

The DCX 22L is the new longer version of the DCX 22S. This brushed DC motor, with a diameter of 22 mm, even outperforms the existing maxon RE 25. With the DCX 22L the same power is achieved, yet with 30% less volume and weight

The GPX gearhead series is also being expanded with two new variants: The GPX 22C is an optimized version of the GPX 22. The improved performance data and life span were achieved by using ceramic axes. Although the same in size, it provides approximately 20% higher torques. Another new member in the maxon GPX family is the low-noise version of the GPX 22. The GPX 22LN has special plastic planet gears in the input stage that reduce operating noise, which mainly occurs in the input stage, by about 5 dBA*.

Ready in 11 days

All configurable DC motors, gearheads and sensors of the maxon DCX program can be ordered online. After only 11 working days, the drive systems are ready to be shipped from Switzerland. Detailed product data can be viewed online immediately, and 3D data for the configuration is available for downloading. Discover more at dcx.maxonmotor.com.

*Measured in accordance with maxon standards, see maxon Catalog 2013/14, page 6.

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

Motion Control – Maxon Introduces the New 4mm Micro Motor and Gearhead!

Maxon Motor was challenged to deliver maximum power in the smallest possible space and the result is the motion control EC 4 brushless motor.

Maxon motion control EC4 Motors and Gearheads

Maxon Logo

Fall River, MA – Motion Control -Maxon motor introduces the EC4, a 4 mm diameter brushless DC motor and gearhead. The typical issue found with micro drives of this size is the output power is too low for the application requirements because of the physical limitations. maxon increased the performance of this tiny motor using the latest winding technology along with the most powerful magnets available. This motor is available in two lengths; short version with 0.5 W nominal power or long version with 1.0 W nominal power.

Maxon also incorporated a high quality motion control gearhead to ensure optimum continuous running. High performance ceramics are used for the gearhead carrier to make the motor capable of high input speeds and drive torques. The speed/torque gradient of the EC 4 is an impressive 50,000 rpm mNm-1 with a continuous torque of 0.4 mNm. There are options on the windings and encoders as well as different reduction ratios on the new 4 mm planetary gearhead.

 

Maxon Motion Control EC4 Motors and Gearheads -Cutaway

This motion control 4 mm brushless DC servo motor is becoming the benchmark solution in miniature pumps, surgical robots, diagnostic devices, endoscopes and anywhere miniaturization is critical. maxon motor has explored the limits of technical boundaries with this EC4 motor development.

For more information and motion control product specifications, visit www.maxonmotorusa.com. or contact us at info@maxonmotorusa.com.