Category Archives: Drives – Brushed

Motion Control – The Mars helicopter makes history – with maxon’s precision motors!

Motion Control – Mars helicopter has maxon’s motors!

Space fans are thrilled: NASA’s Ingenuity helicopter has successfully completed its pioneering flight on Mars. This is the first time in the history of powered, unmanned spaceflight that a device has flown in a controlled manner on another planet.

motion control - mars helicopter


motion control - maxonTaunton, MA — Motion Control Products – A short flight for “Ingenuity,” but a big success for unmanned space flight. NASA’s Mars helicopter flew over the surface of the Red Planet for about 40 seconds on Monday, April 19th and landed back on four legs. From NASA’s perspective, this is a historic event similar to the Wright brothers’ first controlled flight in 1903.

With the Mars helicopter, the concept of powered, unmanned, and autonomous flights on foreign planets is being tested. This is comparable to the first Mars rover “Sojourner”, which paved the way for scientific follow-up missions such as “Curiosity” and currently “Perseverance”. “Ingenuity” is about to complete several flights over a period of 30 days, each lasting up to 90 seconds and reaching a maximum altitude of five meters.

Motion Control – Maxon precision motors Go to Mars AGAIN!

Motion Control – Maxon motors on Mars!

motion control - miniature motors

 

motion control - maxon logo

 

 

Taunton, MA — Motion Control Products – NASA’s Perseverance rover landed on Mars on February 18th. Was there once life on Mars? This is the question that one of the most complex robotic systems ever built by humankind has set out to answer. Several of maxon’s electric drives are used for handling the soil samples—and to control the first Mars helicopter.

Will NASA, the US space agency, successfully land a fifth rover on Mars, allowing it to start its series of missions to bring Mars soil samples back to Earth? The rover named Perseverance will enter the atmosphere of the Red Planet on February 18th—after traveling a distance of more than 470 million kilometers.

Motion Control – ADVANCED Motion Controls releases Micro-sized high-power Servo Drive available from Electromate!

Motion Control – Micro-sized high-power Servo Drive!

motion control - servo drive
motion control - electromate

 

 

Vaughan, Ontario, Canada – Motion Control – The FM060-25-CM is part of a new breed of micro-sized, high-power servo drives, immediately available from ADVANCED Motion Controls. Rated to output 25A continuous and 50A peak, this fully featured digital servo drive is small enough to fit in the tightest locations. It is ideally suited for mobile and portable applications such as mobile robotics, automated mobile robots (AMRs), AGVs, material handling, warehouse automation, lab automation and more.

Motion Control – Protection Against Contamination: Breathing Clean Air!

Motion Control – Protection Suit Motor!

Maxon DC motors are used in the blower components of high-quality protection suits.

motion control Maxon Motor

 


motion control - maxon logoMaxon was selected for the compact and lightweight DC motor design, ironless winding, strong magnet and producing very little vibration and noise output. Most importantly, a brushless DC motor was mandatory as a brushed motor may cause sparks that would ignite within the suit. When designing the suit, special attention was given to the placement of the blower unit sewn inside the suit, to avoid the need for heavy straps or air supply hoses. A Li-Ion battery provides more than four hours of operation of air supply with a flow up to 600 liters per minute.Taunton, MA -Motion Control – Protection suits containing an air blower element that fills the entire suit with clean air, have been used by health professionals when faced with contaminated environments. The COVID-19 pandemic is an unprecedented situation where these type of suits have been utilized. Maxon DC brushless motors are found inside these specialized suits. The DC motor is efficient, high-speed and robust.

 

For more information please contact maxon motor Australia tel. +61 2 9457 7477.

About Maxon

maxon is a developer and manufacturer of brushed and brushless DC motors, as well as gearheads, encoders, controllers, and entire mechatronic systems. With over 50 years of experience in drive technology, maxon works closely with engineers designing high-tech innovations. maxon drives are used wherever the requirements are particularly high: in NASA’s Mars rovers, in surgical power tools, in humanoid robots, and in precision industrial applications. Worldwide, maxon has more than 2800 employees at nine production sites and is represented by sales companies in more than 30 countries. www.maxongroup.com

Contact maxon for more details https://support.maxongroup.com/hc/en-us/requests/new

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

motion control - handbook


See this and other Motion Control Components from Maxon featured on:

http://MotionShop.com.com

http://AllMotionBlogger.com

http://Automation-Blogger.com

http://MotionControlBlogger.com

http://MotionControlBuyersGuide.com

http://MotionControlWeb.com

http://MotionShop.net

http://Catalogs-MotionControl.com

Request 2020/2021 Maxon Catalog

motion control - maxon logo

Motion Control – COVID-19 … Important Information for Ventilator Manufacturers!

Motion Control – ATTENTION – Ventilator Manufacturers!

motion control - ventilator components

 

motion control - electromate

 

 

Vaughan, Ontario, Canada — Motion Control Components — COVID-19 has caused a significant shortage of ventilators for the most seriously ill patients. We are facing a global shortage of equipment and have precious little time to respond.

Electromate is a mechanical ventilator component supplier and works with a number of manufacturing partners that supply crucial components needed to build more ventilators.

These include:

  • HMI’s
  • Linear guides
  • Linear actuators
  • Screw assemblies
  • Compact gearboxes
  • High efficiency servo & stepper motors
  • Programmable motion controllers and drives

Our team of motion design experts are located all across Canada and are available right now to help you with any electro-mechanical ventilator design. If you are working on a ventilator involving rotary, linear, or any other motion, we will provide immediate help with electro-mechanical engineering and component sourcing. Contact us today.

We are already working with ventilator and respirator companies and encourage any other businesses working on COVID-19 solutions to reach out to us.

All inquiries regarding ventilator components or any other equipment to help battle COVID-19 are given utmost priority. We can help to optimize your design quickly and provide fast turnaround proposals as requested. Additionally, we are able to meet high production demands in a very short time by utlilizing ‘Medical Fast Track Programs’ -info.us@maxongroup.com from maxon, and other vendors.

Many of the products we sell to the medical technology sector have ISO 13485 certification. This certification confirms that these products adhere to the fundamental requirements of medical technology and that all processes and procedures are documented, thereby guaranteeing traceability.

In addition to helping with the design and acquisition of critical components used in ventilators and respirators, we also want to make you aware of initiatives that you may be able to utilize. Please read below to learn more about these programs and how you can assist with the COVID-19 cause.

CODE LIFE VENTILATOR CHALLANGE

The Montreal General Hospital Foundation, in collaboration with the Research Institute of the McGill University Health Centre (RI-MUHC), is launching a global innovation challenge, backed by a prize of $200,000 CAD. They are calling for teams to design a simple, low-cost, easy-to-manufacture and easy-to-maintain ventilator which could be deployed anywhere needed to save lives.

To learn more, please visit https://www.mghfoundation.com/en/news/code-life-ventilator-challenge/

 

 

MIT EMERGENCY VENTILATOR (E-VENT) PROJECT COPY

MIT has launched an emergency research project with a team of Engineers and American clinicians to address the question:

Is it possible to safely ventilate a COVID-19 patient by automatically actuating a manual resuscitator?

Their process in approaching this question is to first identify the minimum requirements for a low-cost ventilator, based on the collective wisdom of many clinicians, design against these requirements, conduct immediate testing, report the results, iterate and facilitate discussion.

motion control - electromate

To learn more, please visit https://e-vent.mit.edu/

 

 

About Electromate:

Electromate’s Core Purpose is to help Manufacturers build better machines using differentiated automation technology. They specialize in Robotic and Mechatronic Solutions for the Industrial Automation marketplace. Respected by customers as a premiere source for High Performance Automation and Motion Control Components & Systems, Electromate® specializes in AC & DC Servo and Stepper Motors & Drives, Motion & Automation Controllers, Positioning Systems & Actuators, Feedback Devices, Gearing Products and HMI’s & Operator Displays, all supported via extensive product selection, just-in-timedelivery, dedicated customer service and technical engineering support.

More on Electromate can be found at

Website: http://www.electromate.com

LinkedIn: https://www.linkedin.com/company-beta/209277/

Twitter: https://twitter.com/Electromate

Facebook: https://www.facebook.com/electromateindustrial/

Blog: https://electromate.wordpress.com/

motion control - electromate

For more information on the “Best Place to Work”CLICK HERE!

To view Electromate’s new corporate video CLICK HERE

 

For further information on this new product or others in our extensive product portfolio, call 1-877-SERVO99 (737-8699) or e-mail Warren Osak at sales@electromate.com or visit Electromate at: www.electromate.com


See this and other Motion Control Components from Electromate featured on:

http://MotionShop.com

http://AllMotionBlogger.com

http://Automation-Blogger.com

http://MotionControlBlogger.com

http://motioncontrolBuyersGuide.com

http://MotionControlWeb.com

http://MotionShop.net

http://Catalogs-MotionControl.com

http://MotionControlMarketing.com

http://Gotcha-Stick.com

motion control - electromate logo

Motion Control Application – Driver assist systems can help save lives by alerting driver of potential danger!

Motion Control – Application – Driver Assist Systems Help Save Lives!

 


motion control - maxon logoMaxon A-max 16 brushed DC motor – This drive with a diameter of 16 millimeters (precious metal brushes, 2 Watt) was developed for use with an eccentric weight and a specified bearing.
motion control - application - brushed motors

Fall River, MA — The majority of traffic accidents are caused by human error. In the future, computer-controlled cars will significantly reduce the number of such accidents. Driver assist systems, such as adaptive cruise control (ACC), brake assist systems, or lane departure warning systems (LDW), can save lives. Lane departure warning systems warn the driver if the vehicle is drifting out of its lane. The LDW determines the vehicle’s position in the lane with the use of various optical sensor systems and computers. If the car is in danger of drifting out of the lane, the system activates an electric motor in the steering wheel that causes the wheel to vibrate, warning the driver.

A luxury car manufacturer has engaged maxon to supply the motors for this application. The base DC brushed motor is maxon’s A-max 16 (precious metal brushes, 2 W), modified for the application with an eccentric weight and a specified bearing. In order to prevent the other vehicle systems from being affected by the electromagnetic fields of the motor, it has been equipped with special EMI suppression for automotive applications. The small drive system must meet specific requirements: It needs to be low-noise, dynamic, feature high power density, and fit in a narrow space – requirements that maxon’s small A-max 16 easily masters..

Contact maxon for more details info@maxonmotorusa.com

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

motion control - handbook


See this and other Motion Control Components from Maxon featured on:

http://MotionShop.com.com

http://AllMotionBlogger.com

http://Automation-Blogger.com

http://MotionControlBlogger.com

http://MotionControlBuyersGuide.com

http://MotionControlWeb.com

http://MotionShop.net

http://Catalogs-MotionControl.com

Request 2020/2021 Maxon Catalog

motion control - maxon logo

Motion Control – AMC introduces the FE060-25-EM – FlexPro™ Digital Servo Drive!

Motion Control – Digital Servo Drive

Motion Control Digital Drive

 

Motion Control - Electromate-Logo

 

Vaughan, Ontario, Canada — Motion Control Components — Available immediately, the FE060-25-EM is the first servo drive of the new FlexPro™ digital drive family from ADVANCED Motion Controls (AMC). Designed with compact form and power density in mind, the micro-sized FE060-25-EM can outperform larger-sized digital servo drives and still be integrated into tight spaces.

At just 1.5 x 1 x 0.6 inches (38 x 25 x 16 mm) in size, the footprint of the drive is approximately the same as two standard postage stamps. In other words, four of these drives can fit on a standard business card. Even with its small size, the FE060-25-EM can supply brushed, brushless, stepper, and linear servo motors with up to 25 amps continuous current and 50 amps peak current.

Features include:

  • 1.5 x 1 x 0.6 inches (38 x 25 x 16 mm) in size
  • 10-55 VDC supply voltage
  • 25A continuous current
  • 50A peak current
  • Highest power density servo drive from ADVANCED Motion Controls to date
  • EtherCAT Communication
  • Incremental encoder and BISS C-mode feedback
  • Torque, velocity, and position operating modes
  • Configuration and full loop tuning
  • IMPACT™ architecture

A developer version is available for proof-of-concept and testing purposes – part number FD060-25-EM. It comes with an FE060-25-EM soldered to a larger board that is equipped with various connectors for simplified interfacing.

Projected Industries & Applications:

The small size of the FE060-25-EM makes it perfect for cobots (collaborative robots), AGVs, portable devices, lab and warehouse automation, military equipment, and any other integrated design.

About FlexPro™

FlexPro™ is AMC’s newest family of digital servo drives. With cutting edge engineering, FlexPro™ is meant to expand the capabilities of AMC’s already powerful and diverse product selection. The IMPACT™ architecture allows FlexPro™ servo drives to maintain the intelligence and power of larger-sized servo drives while fitting into much more compact packages. The FE060-25-EM is the first drive in the series with many more to come.

About IMPACT™

IMPACT™ (Integrated Motion Platform And Control Technology) is the architecture that makes AMC’s FlexPro™ drives possible. The stacking of circuit boards with creative selection and placement of high-power components allows for much higher power density than previously produced servo drives. The expanded processing capabilities ensure the drive’s intelligence is unmatched. IMPACT™ makes its debut with the FE060-25-EM. This technology will be used in subsequent FlexPro™ drives as well as any future custom products where it is desired.

 

About ADVANCED Motion Controls

ADVANCED Motion Controls, a U.S. company in business for over 31 years, was founded with the idea of designing and manufacturing lower cost / higher power density servo drives. The company’s focus remains to create and deliver the best motion control drives for brushed or brushless servo motors. With approximately 3 million servo axes shipped, ADVANCED Motion Controls has become one of the fastest growing servo drive companies in the world.

CLICK HEREFor information on the FE060-25-EM from Advanced Motion Controls can be viewed at:

About Electromate:

Electromate’s Core Purpose is to help Manufacturers build better machines using differentiated automation technology. They specialize in Robotic and Mechatronic Solutions for the Industrial Automation marketplace. Respected by customers as a premiere source for High Performance Automation and Motion Control Components & Systems, Electromate® specializes in AC & DC Servo and Stepper Motors & Drives, Motion & Automation Controllers, Positioning Systems & Actuators, Feedback Devices, Gearing Products and HMI’s & Operator Displays, all supported via extensive product selection, just-in-timedelivery, dedicated customer service and technical engineering support.

More on Electromate can be found at

Website: http://www.electromate.com

LinkedIn: https://www.linkedin.com/company-beta/209277/

Twitter: https://twitter.com/Electromate

Facebook: https://www.facebook.com/electromateindustrial/

Google+: https://plus.google.com/104057418684128701566

Blog: https://electromate.wordpress.com/

Electromate Best Blace to Work

For more information on the “Best Place to Work”CLICK HERE!

To view Electromate’s new corporate video CLICK HERE

To see all of Electromate’s Products and Application Stories featured on MotionShop.com, enter electromate in the Google custom search box (upper left, above)

For further information on this new product or others in our extensive product portfolio, call 1-877-SERVO99 (737-8699) or e-mail Warren Osak at sales@electromate.com or visit Electromate at: www.electromate.com

See this and other Motion Control Components from Electromate featured on:
http://MotionShop.com
http://AllMotionBlogger.com
http://Automation-Blogger.com
http://MotionControlBlogger.com
http://MotionControlWeb.com
http://MotionShop.net

 

Motion Control - Electromate-Logo
Visit our Website
Motion Control - Electromate Twitter Link
Motion Control - Electromate Facebook Link

Motion Control – Panel Mount Servo Drive Offers Centralized Control & High Bandwidth & Quick Response Times!

motion control servo drive

The AB25A100 PWM servo drive from Advanced Motion Controls is designed to drive brushless and brushed DC motors at a high switching frequency.

Servo2Go-Logo

Greenville, DE —-Motion Control Components – The drive is fully protected against overvoltage, under-voltage, over-current, over-heating and short-circuits across motor, ground and power leads. Furthermore, the drive can interface with digital controllers or be used stand-alone, and requires only a single unregulated DC power supply. Loop gain, current limit, input gain and offset can be adjusted using 14-turn potentiometers. The offset adjusting potentiometer can also be used as an on-board input signal for testing purposes. This drive can use quadrature encoder inputs for velocity control.

Features include:

  • 20-80 VDC Input, 15 A Cont. (25 Peak) Output
  • Built-in hardware protection – Over Current, Over Voltage, Under Voltage, Over Temperature, Short Circuit
  • DIP Switches and Potentiometers for loop tuning, current limit adjustments and drive configuration
  • Standard models support both brushless and brushed motor types
  • Velocity feedback via incremental encoder, Hall Sensors, or tachometer
  • Optical isolation between high and low power signals standard on certain models
  • Current, Velocity, and Fault Monitor analog output signals
  • Status LEDs for power and drive status
  • Four quadrant regenerative operation

CLICK HERE for more information on the AB25A100 Servo Drive from Advanced Motion Controls.

These and other Motion Control Products are available through www.Servo2Go.com

For further information on this new product or others in our extensive product portfolio, call 1- 877-378-0240 or e-mail Warren Osak atwarren@servo2go.com or visit Servo2Go.com at: www.Servo2Go.com

Servo2Go-Logo
Visit our Website
Twitter Link
Facebook Link

Motion Control Application- Maxon Is A Part of NASA’s InSight Mission!

Swiss motor ventures deep under the surface of Mars.

 

Maxon Logo

 

Fall River, MA — Motion Control Components Application – The InSight probe landed on Mars to shed new light on the formation of rocky planets. The mission entails driving a measuring probe five meters deep into the Martian ground. maxon engineers pulled out all the stops to make their motor fit for the job.

Tension was mounting among fans of space exploration, as the robotic InSight probe landed on Mars on November 26. If all goes according to plan, the stationary lander will proceed to carry out various measurements over a period of two years and provide important insights into Mars and the formation of Earth. The mission is being conducted by the Jet Propulsion Laboratory (JPL) for NASA.

 

Motor rams penetrometer 5 meters deep into the ground

DC motors from the Obwalden-based drive specialist maxon motor are also on board. A compact motor-gearhead combination with a diameter of 22 millimeters is used in the HP3 probe developed by the German Aerospace Center (DLR). It is designed to determine the temperature profile of the planet. Specifically, the maxon drive is located in a rod-shaped penetrometer, nicknamed “the Mole” by the developers. This penetrometer is autonomously driven five meters into the ground. To achieve this, the motor tensions a spring with each revolution. The spring then releases with great force, executing a powerful downward punch. In this way, the “Mole” gradually burrows downwards – over a period of several weeks, pulling along a cable that is equipped with sensors to help the researchers determine the thermal state of the interior of Mars and draw conclusions about its origin. Since Mars is a rocky planet like Earth, the scientific results may also help gain a better understanding of our own planet.

Special solution for more than 400 g

Mars is not a very friendly environment for technology. Nonetheless, more than a hundred maxon drives have already proven their worth on the Red Planet. The current InSight mission, however, posed additional challenges for the Swiss engineers. To efficiently drive the penetrometer into the ground, the DC motor needs to withstand forces in excess of 400 g – and more than 100,000 times. It took a number of variations and failed tests to find the right solution. The result is a standard DCX 22 motor, greatly modified with additional welding rings, bearing welds and specially shortened brushes. The utilized GP 22 HD gearhead, on the other hand, only needed Mars-specific lubrication.

Say hello to an old acquaintance

The InSight probe is powered by two solar panels for the duration of its mission. To save costs, JPL repurposed designs from the successful Phoenix mission, using a maxon DC motor developed some time ago to extend the solar panels. This type of motor, an RE 25, has ensured that NASA’s Opportunity rover has been active on Mars for more than 14 years (even if it is currently in deep sleep due to a sandstorm). Thus, two generations of maxon drives come together in the InSight robot probe to jointly contribute to the mission’s success.

Contact maxon for more details info@maxonmotorusa.com

Comprehensive documentation and software are included with every delivery, and are also available for you to download from our website at www.maxonmotor.com.

Maxon Logo
Visit our Website
Order Our Catalog

 

Maxon Handbook Banner

Motion Control Components – New EtherCAT Drive from Galil Motion Control!

Motion Control - Electromate-Logo
Visit our Website
Motion Control - Electromate Twitter Link
Motion Control - Electromate Facebook Link

 

Vaughan, Ontario, Canada — Motion Control Components — The EDD-3701x EtherCAT slave drive joins Galil’s EtherCAT Family. This family has grown to include two EtherCAT masters and an I/O slave with both digital and analog I/O points. The EDD-3701x is a motor amplifier that operates in an EtherCAT distributed system where there are up to 32 slave drives and one master. It has a daisy chain topology using standard CAT5 Ethernet cables. The EDD-3701x can interface with Galil masters (DMC-500×0 and DMC-52xx0) for sophisticated applications or with TwinCAT® for very simple applications.

The EDD-3701x series has the ability to control brushed, brushless, steppers, and microstepping motors (See Table 1 for more details). Unlike the competition, the EDD-3701x can both control a motor and also has 8 digital inputs, 4 digital outputs, 2 analog inputs, and 2 analog outputs. All I/O information from these drives are accessible by the EtherCAT master. This capability can eliminate the need for separate EtherCAT I/O devices. The configuration of the EDD-3701x is done using the Galil’s GDK software. Simply connect to a PC via EDD-3701x’s USB port, follow the GDK configuration tool process, and start moving motors. The EDD-3701x also comes with a setup guide to get the user from taking the EDD out of the box to moving motors in a manner of minutes

The EDD-3701x has a small form factor with just 3.9”x5.0”x1.5”. It can operate in either Cyclic Synchronous Position mode (CSP) or Cyclic Synchronous Torque mode (CST). It also accepts quadrature encoder feedback up to 15 MHz.

 

CLICK HERE For additional information on the EDD-3701x EtherCAT Slave Drive

About Electromate:

Electromate’s Core Purpose is to help Manufacturers build better machines using differentiated automation technology. They specialize in Robotic and Mechatronic Solutions for the Industrial Automation marketplace. Respected by customers as a premiere source for High Performance Automation and Motion Control Components & Systems, Electromate® specializes in AC & DC Servo and Stepper Motors & Drives, Motion & Automation Controllers, Positioning Systems & Actuators, Feedback Devices, Gearing Products and HMI’s & Operator Displays, all supported via extensive product selection, just-in-timedelivery, dedicated customer service and technical engineering support.

More on Electromate can be found at

Website: http://www.electromate.com

LinkedIn: https://www.linkedin.com/company-beta/209277/

Twitter: https://twitter.com/Electromate

Facebook: https://www.facebook.com/electromateindustrial/

Google+: https://plus.google.com/104057418684128701566

Blog: https://electromate.wordpress.com/

Electromate Best Blace to Work

For more information on the “Best Place to Work”CLICK HERE!

To view Electromate’s new corporate video CLICK HERE

To see all of Electromate’s Products and Application Stories featured on MotionShop.com, enter electromate in the Google custom search box (upper left, above)

For further information on this new product or others in our extensive product portfolio, call 1-877-SERVO99 (737-8699) or e-mail Warren Osak at sales@electromate.com or visit Electromate at: www.electromate.com

Motion Control – 510 Series DC and Brushless Servo Motor Drivers from MotiCont!

MotiCont-Logo

Van Nuys, CA – Motion Control – This series of drivers is a high performance, cost effective servo motor driver to implement intelligent motion control. The driver incorporates an advanced architecture and surface mount technology to achieve an exceptional power density. This series is designed to drive voice coil, brush-type and brushless DC motors at a high switching frequency. They receive step and direction signals or analog signal from motion controller.

 

There 3 models of the 510 Series DC and Brushless Servo Motor Drivers:

510-01 Servo Motor Driver,up to +80 VDC Power Supply, 12 Amps Maximum Currentt

510-02 Servo Motor Driver,up to +80 VDC Power Supply, 20 Amps Maximum Current

510-03 Servo Motor Driver,up to +80 VDC Power Supply, 40 Amps Maximum Current
Features of 510 Series DC and Brushless Servo Motor Drivers:

  • Runs DC and Brushless Servo Motors
  • Four Quadrant Regenerative Operation
  • Space Vector Modulation (SVM) Technology
  • Fully Digital State-of-the-art Design
  • Programmable Current, Velocity and Position Loops Gain Settings
  • Fully Configurable Current, Voltage, Position Limits
  • PIDF Velocity Loop
  • PID + FF Position Loop
  • 12 Amps Motor Output
  • +20 VDC to +80 VDC Power Supply
  • Protected Against Over Current
  • Built-in Signal Generator, Sinusoidal, Square Wave and Triangular
  • 20 KHz PWM Frequency
  • No Tachometer Feedback Needed
  • 0 ºC to 70 ºC Operating Temperature
  • Modular 2-Piece Power, Motor, Signal Connector

510 Series DC and Brushless Servo Motor Drivers Modes of Operation:

  • Current
  • Velocity
  • Position

Command Source for 510 Series DC and Brushless Servo Motor Drivers:

  • Encoder Following
  • 10 V Analog
  • Step and Direction

Feedback Supported by 510 Series DC and Brushless Servo Motor Drivers:

  • Incremental Encoder
  • 10 V Analog
  • Auxiliary Incremental Encode

To order 510 Series DC and Brushless Servo Motor Drivers online Click Here!

For additional information contact MotiCont, “A Motion Company” at 6901 Woodley Avenue, Van Nuys, CA 91406, USA; Tel: , Fax: (818) 785-5713, E-Mail: moticont@moticont.com or visit the website at http://www.moticont.com

MotiCont-Logo
Visit our Website
Videos

Motion Control – 6 New Servo Drives capable of 100A peak and 60A continuous output!

Motion Control Components - Electromate offers 6 new Servo Drives

 

Motion Control - Electromate-Logo

 

This new power range comes with a variety of network options including EtherCAT, CANopen, POWERLINK, Modbus and more … 

 

Vaughan, Ontario, Canada — Motion Control Components — This new power range comes with a variety of network options including EtherCAT, CANopen, POWERLINK, Modbus and more. Safe Torque Off (STO) functionality is included as a standard feature. Available now, these new models offer high efficiency in a compact design and are targeted towards AGVs and mobile applications

 

Specifications:

  • 100 A Peak Current Output
  • 60 A Continuous Current Output
  • 20 – 80 VDC Supply Voltage
  • Safe Torque Off (STO) standard
  • High Efficiency
  • Compact Design

 

Information on the 6 new servo drives from Advanced Motion Controls can be found at the links below:

DPCANIA-100B080 (CANopen)

DPCANIE-100B080 (CANopen)

DPEANIU-100B080 (EtherCAT)

DPMANIU-100B080 (Click&Move® Embedded)

DPPANIU-100B080 (POWERLINK / Modbus TCP / Ethernet)

DPRANIE-100B080 (Modbus RTU / RS485)

About Electromate:

Electromate’s Core Purpose is to help Manufacturers build better machines using differentiated automation technology. They specialize in Robotic and Mechatronic Solutions for the Industrial Automation marketplace. Respected by customers as a premiere source for High Performance Automation and Motion Control Components & Systems, Electromate® specializes in AC & DC Servo and Stepper Motors & Drives, Motion & Automation Controllers, Positioning Systems & Actuators, Feedback Devices, Gearing Products and HMI’s & Operator Displays, all supported via extensive product selection, just-in-timedelivery, dedicated customer service and technical engineering support.

More on Electromate can be found at

Website: http://www.electromate.com

LinkedIn: https://www.linkedin.com/company-beta/209277/

Twitter: https://twitter.com/Electromate

Facebook: https://www.facebook.com/electromateindustrial/

Google+: https://plus.google.com/104057418684128701566

Blog: https://electromate.wordpress.com/

To view Electromate’s new corporate video CLICK HERE

For further information on this new product or others in our extensive product portfolio, call 1-877-SERVO99 (737-8699) or e-mail Warren Osak at sales@electromate.com or visit Electromate at: www.electromate.com

 

Motion Control - Electromate-Logo
Visit our Website
Motion Control - Electromate Twitter Link
Motion Control - Electromate Facebook Link

Motion Control – Panel Mount Servo Drive Provides Centralized Control & Offers High Bandwidth & Quick Response Times!

Motion Control Component - Panel Mount Servo Drive from Servo2Go

Servo2Go-Logo

Greenville, DE —-Motion Control Components – The AB25A100 PWM servo drive from Advanced Motion Controls is designed to drive brushless and brushed DC motors at a high switching frequency. A single red/green LED indicates operating status. The drive is fully protected against overvoltage, under-voltage, over-current, over-heating and short-circuits across motor, ground and power leads. Furthermore, the drive can interface with digital controllers or be used stand-alone, and requires only a single unregulated DC power supply. Loop gain, current limit, input gain and offset can be adjusted using 14-turn potentiometers. The offset adjusting potentiometer can also be used as an on-board input signal for testing purposes. This drive can use quadrature encoder inputs for velocity control. Features include:

  • Built-in hardware protection – Over Current, Over Voltage, Under Voltage, Over Temperature, Short Circuit
  • DIP Switches and Potentiometers for loop tuning, current limit adjustments and drive configuration
  • Standard models support both brushless and brushed motor types
  • Velocity feedback via incremental encoder, Hall Sensors, or tachometer
  • Optical isolation between high and low power signals standard on certain models
  • Current, Velocity, and Fault Monitor analog output signals
  • Status LEDs for power and drive status
  • Four quadrant regenerative operation

CLICK HERE for more information on the AB25A100 Servo Drive from Advanced Motion Controls.

These and other Motion Control Products are available throughwww.Servo2Go.com

For further information on this new product or others in our extensive product portfolio, call 1- 877-378-0240 or e-mail Warren Osak at warren@servo2go.com or visit Servo2Go.com at: www.Servo2Go.com

Servo2Go-Logo
Visit our Website
Twitter Link
Facebook Link

Motion Control – EtherCAT Servo Amplifiers feature High speed, Deterministic Control!

Motion Control AMC EtherSAT Drives from Servo2Go

AMC Extends the popular DigiFlex® Performancex product line. Their EtherCAT communication servo drives now provides for multiple feedback devices in a variety of power platforms.

Servo2Go-Logo

Greenville, DE —– Motion Control Components – Advanced Motion Controls provides products for the fastest, most flexible form of industrial Ethernet control – EtherCAT®. High speed, deterministic control with standard 100 base-T hardware, EtherCAT Servo Amplifiers are industry proven to achieve blazing fast, consistent results in demanding applications.

Extending the popular DigiFlex® Performance™ product line our EtherCAT communication servo drives provide for multiple feedback devices in a variety of power platforms. Advanced Motion Controls EtherCAT products consist of panel mount and plug-in servo drives to allow for quick prototyping and ease of system integration. Panel mount DPE drives serve as nodes in single or multi-axis EtherCAT networks, while plug-in DZE/DZS drives utilize AMC’s unique, proprietary high speed multi-axis communication interface and I/O expansion capabilities (‘DxM’™ and ‘DxI/O’™ Technologies). Now a single EtherCAT node can accommodate a combination of up to 4 axes of motion with 32 digital inputs, 32 digital outputs, 4 analog inputs, and 2 analog outputs each. The result is a highly integrated high value motion control solution for single or multi-axis applications.

AMC’s EtherCAT Servo Drives feature:

  • Four Quadrant Regenerative Operation
  • Space Vector Modulation (SVM) Technology
  • Fully Digital State-of-the-art Design
  • Programmable Gain Settings
  • Fully Configurable Current, Voltage, Velocity and Position Limits
  • PIDF Velocity Loop and PID + FF Position Loop
  • Compact Size, High Power Density
  • 12-bit Analog to Digital Hardware
  • Supports Advanced MotionControls’ ‘DxM’ Technology
  • On-the-Fly Mode Switching and On-the-Fly Gain Set Switching

More information on the EtherCAT Servo Amplifiers from Advanced Motion Controls available from Servo2Go.com can be viewed at: https://www.electromate.com/advanced-motion-controls.html

These and other Motion Control Products are available through www.Servo2Go.com

For further information on this new product or others in our extensive product portfolio, call 1- 877-378-0240 or e-mail Warren Osak at warren@servo2go.comor visit Servo2Go.com at: www.Servo2Go.com

Servo2Go-Logo
Visit our Website
Twitter Link
Facebook Link

Motion Control – AMC’s µZ Plug-In Servo Drives available from Electromate!

Electromate offers Micro Z Plug-In Servo Drives from Advanced Motion Controls

Motion Control - Electromate-Logo

Vaughan, Ontario, Canada — Motion Control – µZ’s are the smallest off-the-shelf servo drives from ADVANCED Motion Controls. Pronounced ‘Micro-Z’ these plug-in drives are designed for embedded applications in a wide range of industries including: Robotics, Lab Automation, Homeland Security/Military, Electric Mobility, Medical and Packaging.

µZ servo drives are designed to drive brushless and brushed DC motors at a high switching frequency. To increase system reliability and to reduce cabling costs, the drives are designed for direct integration into your PCB. Weighing in at less than 9 grams, µZ Drives output 10A peak and 5A continuous and operate with a bus voltage range of 10-36VDC.

Designed without the need for a heatsink, the µZ’s are true featherweights with a high power to weight ratio. The µZ’s are fully protected against over-voltage, under-voltage, over-current, over-heating, and short-circuits. Depending on the model, the drives interface with digital controllers that have analog ±10V or PWM/Direction commands. These servo drives require only a single unregulated isolated DC power supply, and are fully RoHS (Reduction of Hazardous Substances) compliant.

Datasheets and Support:

AZB10A4 for ±10V Command Signals, Current Mode

AZBH10A4 for ±10V Command Signals, Hall Velocity Mode

AZBD10A4 for ±10V Command Signals, Duty Cycle Mode

AZBDC10A4 for PWM/Direction Command Signals

Stand-alone (drives with built-in interface)

AZB10A4IC for ±10V Command Signals, Current Mode

AZBDC10A4IC for PWM/Direction Command Signals

Additional features and benefits include:

  • Designed for direct board-to-board integration.
  • No heatsink and no need for additional heatsinking results in the smallest installed volume
  • Feather weight, less than 9 grams
  • Dimensions (mm) 38.1 x 38.1 x 7.34 for current mode models, 43.2 x 38.1 x 9.4 for velocity / duty cycle models
  • Dimensions (in) 1.50 x 1.50 x 0.29 for current mode models, 1.70 x 1.50 x 0.37 for velocity / duty cycle models
  • Large operational temperature range, 0-85°C
  • Compatible with low inductance motors
  • Smallest form factor of any off-the-shelf servo drive from ADVANCED Motion Controls
  • 40 kHz switching frequency

For further information on this new product or others in our extensive product portfolio, call 1-877-SERVO99 (737-8699) or e-mail Warren Osak at sales@electromate.comor visit Electromate at: www.electromate.com

Motion Control - Electromate-Logo
Visit our Website
Motion Control - Electromate Twitter Link
Motion Control - Electromate Facebook Link